mtk-20170518, branch v18.06.0

OpenWrt v18.06.0: adjust config defaults

2018-07-30T16:30:59+00:00

Signed-off-by: Jo-Philipp Wich

Revert "ar71xx: define switch for rb-952ui-5ac2nd"

2018-07-30T16:25:17+00:00

This reverts commit 3442ec5d5724ca747c9f76b949dc8d21c94228c0.

The device behaviour is reportedly erratic so let's not take chances and
leave this out for now.

Signed-off-by: Jo-Philipp Wich

ar71xx: define switch for rb-952ui-5ac2nd

2018-07-30T16:14:17+00:00

QCA9533 built-in switch can be configured

Tested-by: Thibaut VARÈNE 
Signed-off-by: Thibaut VARÈNE 
(cherry picked from commit 0e43c31ebde996ca88f5857bb7e6c4cbf3f65756)

imagebuilder: add function to show manifest

2018-07-30T14:33:57+00:00

Tested with 18.06.0-rc2/ar71xx/generic/tl-wdr4300-v1, image & list

This PR is based on the work of @fewckert[1] with slight improvements.

Add function `manifest` to show the manifest of the produced image,
before actually building it. The manifest contains an orderd list of
package name and version.

This is usefull to check package dependencies but also determine a
unique and reproducible image name before building the package. The
sysupgrade server[2] builds images on request with individual package
selection. To distignish between created images which contain differnt
packages, the EXTRA_IMAGE_NAME is set to a shortend hash of the
manifest's content. So far the image was renamed afterwards as the
manifests content was unknown, however this corrupts the signed
sha256sums. This patch allows a clean solution as to dtermine the
manifest in advance and set the EXTRA_IMAGE_NAME accordingly.

[1]: https://github.com/lede-project/source/pull/1591
[2]: https://github.com/aparcar/attendedsysupgrade-server

Signed-off-by: Paul Spooren 
(cherry-picked from commit 869b0d11db)

ar71xx:add support for E750G v8

2018-07-30T12:02:41+00:00

Qxwlan E750G v8 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (PoE support)
 - 2x 10/100/1000 Mbps Ethernet
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 
(cherry picked from commit 53a45020135b504cb4bee0fa8d98c8eaf6391066)

ar71xx:add support for E750A v4

2018-07-30T12:02:40+00:00

Qxwlan E750A v4 is based on Qualcomm QCA9344.

Specification:

 - 560/450/225 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 5G GHz (AR9344)
 - 2x 10/100 Mbps Ethernet (one port with PoE support)
 - 1x miniPCIe slot (USB 2.0 bus only)
 - 7x LED (6 driven by GPIO)
 - 1x button (reset)
 - 1x DC jack for main power input (9-48 V)
 - UART (J23) and LEDs (J2) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 
(cherry picked from commit ac03d51a3f4daa2f6a2a83f041dcd71674a9f724)

ar71xx:add support for E558 v2

2018-07-30T12:02:40+00:00

Qxwlan E558 v2 is based on Qualcomm QCA9558 + AR8327.

Specification:

 - 720/600/200 MHz (CPU/DDR/AHB)
 - 128 MB of RAM (DDR2)
 - 8/16 MB of FLASH (SPI NOR)
 - 2T2R 2.4 GHz (QCA9558)
 - 3x 10/100/1000 Mbps Ethernet (one port with PoE support)
 - 4x miniPCIe slot (USB 2.0 bus only)
 - 1x microSIM slot
 - 5x LED (4 driven by GPIO)
 - 1x button (reset)
 - 1x 3-pos switch
 - 1x DC jack for main power input (9-48 V)
 - UART (JP5) and LEDs (J8) headers on PCB

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Signed-off-by: 张鹏 
(cherry picked from commit b74f63f81d6121b5eace3f0c0c87399f7e0fde92)

brcm2708: split sdcard.img.gz into a sysupgrade and factory image

2018-07-30T12:00:59+00:00

@vahid-dan reported a issue with extracting the rpi images with
Gnome's Archive Manager:
"Ubuntu Archive Manager cannot extract the file and it just
throws a general error message: "An error occurred while
extracting files".


@blogic told me to split the single sdcard.img.gz for the RPi
into a sysupgrade and a factory image for all brcm2708 targets.
The factory images will have no metadata attached, this way
these utilities that can't deal with the attached metadata will
not fail for no reason.

Cc: John Crispin 
Signed-off-by: Christian Lamparter 
(cherry picked from commit 7516a960113d512cb2909f40bd07caf2a6c547b1)

base-files: network.sh: gracefully handle missing network.interface ubus ns

2018-07-30T11:19:19+00:00

When attempting to use any of the functions in network.sh while netifd is
not started yet, the ubus interface dump query will fail with "Not found",
yielding an empty response.

Subsequently, jsonfilter is invoked with an empty string instead of a valid
JSON document, causing it to emit a second "unexpected end of data" error.

This caused the dnsmasq init script to log the following errors during
early boot on some systems:

    procd: /etc/rc.d/S19dnsmasq: Command failed: Not found.
    procd: /etc/rc.d/S19dnsmasq: Failed to parse json data: unexpected end of data.

Fix the issue by allowing the ubus query to fail with "Not found" but still
logging other failures, and by passing an empty JSON object to jsonfilter
if the interface status cache is empty.

Signed-off-by: Jo-Philipp Wich

iwinfo: update to version 2018-07-24

2018-07-30T09:21:25+00:00

Update to new iwinfo version.
Adds support for channel survey.
Adds ubus support.
Etc.

Signed-off-by: Nick Hainke 
(cherry picked from commit 296ae7ab89c179ff39feff973000fcb864754df7)