mtk-20170518/package/base-files/files/bin, branch master

base-files: do not add relevant sections & options except when ipv6 is support in kernel

2018-08-06T10:08:47+00:00

Signed-off-by: Rosy Song

linux-atm: add br2684ctl option to specify the netdev name

2018-01-10T07:08:53+00:00

Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.

It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.

Signed-off-by: Martin Schiller 
Signed-off-by: Mathis Kresin

merge: base: update base-files and basic config

2017-12-08T18:41:18+00:00

Signed-off-by: Zoltan HERPAI

base-files: fix wan6 interface config generation for pppoe

2017-09-18T07:57:34+00:00

Setting ipv6 to auto in case of a pppoe interface will trigger the
creation of a dynamic wan_6 interface meaning two IPv6 interfaces
(wan6 and wan_6) will be active on top of the pppoe interface.
This leads to unpredictable behavior in the network; therefore set
ipv6 to 1 which will prevent the dynamic creation of the wan_6
interface.
Further alias the wan6 interface on top of the wan interface for pppoe
as the wan6 interface can only be started when the link local address is
ready. In case of pppoe the link local address is negotiated during the
Internet Protocol Control Protocol when the PPP link is setup meaning
all the IP address info is only available when the wan interface is up.

Signed-off-by: Hans Dedecker

base-files: uppercase default hostname: LEDE

2017-01-26T17:10:10+00:00

The name will appear in shell prompt and LuCI page title.  Uppercase
letters seem to be more vigorous

Signed-off-by: Yousong Zhou

base-files: Changed UCI variable name for GPIO value from 'default' to 'value'

2016-12-12T08:57:40+00:00

This changes the UCI variable for the GPIO value from system.$cfg.default back
to system.$cfg.value as it was before the change from uci-defaults [1] to board.d.
/etc/init.d/gpio_switch [2] still expects the value to be in system.$cfg.value.

[1] https://github.com/lede-project/source/blob/d65916047b44d6d157d88d15e8e3d92555c5e6f8/package/base-files/files/lib/functions/uci-defaults.sh#L197
[2] https://github.com/lede-project/source/blob/master/package/base-files/files/etc/init.d/gpio_switch#L17

Signed-off-by: Julian Labus

base-files: add ucidef_set_led_usbport for full usbport support

2016-10-22T09:16:01+00:00

This helper allows using usbport trigger directly. It requires usbport
compatible syntax and supports specifying multiple USB ports, e.g.:
ucidef_set_led_usbport "usb" "USB" "devicename:colour:function" "usb1-port1" "usb2-port1"

This adds a proper object to the board.json, e.g.
"usb": {
	"name": "USB",
	"type": "usbport",
	"sysfs": "devicename:colour:function",
	"ports": [
		"usb1-port1",
		"usb2-port1"
	]
}
and supports translating it into uci section.

Signed-off-by: Rafał Miłecki

base-files: also generate configs when current is empty (FS#193)

2016-10-05T17:59:11+00:00

Before a configuration is generated, an empty file is created to store
it in. (required by UCI)

If something happens during config generation
(power cut, interruption, ..) an empty file exists and it is never
regenerated again, causing some daemons to fail starting
(NTPD, logread, ..)

Fix this by also generating new configs if a critical file
is empty.

Signed-off-by: Koen Vandeputte

base-files: board_detect: allow specifying the generated file

2016-08-13T13:49:51+00:00

Allow passing a filename to change the location of the generated
board.json.

Signed-off-by: Jonas Gorski

base-files: let config_generate call board_detect

2016-08-13T13:49:46+00:00

Instead of board_detect generating the config as a side effect, let
config_generate call board_detect as needed.

Signed-off-by: Jonas Gorski