Rename subtargets 32b/64b with armv8_32b/armv8_64b which are more proper, and update makefile files. There also will be other subtargets added in the future, like armv7. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Backport kernel patches for LS1043A Rev1.1 support from upstream, patchwork, and SDK. And update to latest u-boot to support LS1043A Rev1.1. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Do not put the u-boot and ucode images into the kernel build directory as this directory might get removed after kernel updates while the u-boot packages InstallDev recipe is not getting re-executed because it is still considered current, leading to image build failures later on due to missing images. To ensure that built bootloader images persist over kernel version updates in the buildroot, put them into the new STAGING_DIR_IMAGE directory. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also use default defintions for PKG_SOURCE_SUBDIR, PKG_SOURCE Signed-off-by: Felix Fietkau <nbd@nbd.name>
Replace *MD5SUM with *HASH, replace MD5 hashes with SHA256 Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add support for NXP layerscape ls1046ardb 64b/32b Dev board. LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot * USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port * UART: supports two UARTs up to 115200 bps for console Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
The QorIQ LS1012A processor, optimized for battery-backed or USB-powered, integrates a single ARM Cortex-A53 core with a hardware packet forwarding engine and high-speed interfaces to deliver line-rate networking performance. QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance development platform, with a complete debugging environment. The LS1012ARDB board supports the QorIQ LS1012A processor and is optimized to support the high-bandwidth DDR3L memory and a full complement of high-speed SerDes ports. LEDE/OPENWRT will auto strip executable program file while make. So we need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network fiemware be destroyed, then run make to build ls1012ardb firmware. The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message. This issue have noticed the IP owner for investigate, hope he can solve it earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4" bootargs. Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
Add support for NXP layerscape ls1043ardb 64b/32b Dev board. LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores. ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC, I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc. 64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from NXP QorIQ SDK release. All of 4.4 kernel patches porting from SDK release or upstream. QorIQ SDK ISOs can be downloaded from this location: http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>