mtk-20170518/package/firmware, branch v18.06.0-rc2 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ipq40xx: add support for ZyXEL WRE6606 2018-06-21T05:02:37+00:00 Magnus Frühling skorpy@frankfurt.ccc.de 2018-06-11T21:10:43+00:00 36234df96c6e468cf15c7e25ad2c4d7945478637 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com> (cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f) 
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	128 MB Nanya NT5CC64M16GP-DI
FLASH:	16 MiB Macronix MX25L12845EMI-12G
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT:  WPS, Mode-toggle-switch
LED:	Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
        (LAN not controllable by software)
        (WLAN each green / red)
SERIAL:	Header next to eth-phy.
        VCC, TX, GND, RX (Square hole is VCC)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet (Correct MAC-address)
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from tftp
 - OpenWRT sysupgrade
 - LEDs
 - WPS Button

Not Working:
 - Mode-toggle-switch

Install via TFTP:

Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.

To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.

append-cmdline patch taken from chunkeeys work on the NBG6617.

Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
(cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f)
linux-firmware: Add firmware for usb-serial-ti-usb 2018-05-15T04:39:46+00:00 David Woodhouse dwmw2@infradead.org 2017-02-16T00:23:27+00:00 4424a9ff205dc9c7a10652344c95dc4290efdb58 Signed-off-by: David Woodhouse <dwmw2@infradead.org> 
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ipq-wifi: drop custom board-2.bins 2018-04-23T20:07:22+00:00 Sven Eckelmann sven.eckelmann@openmesh.com 2018-04-19T07:12:22+00:00 e6bd568051c7ca77a59783fe50203f6e2a427f19 The BDFs for all boards were upstreamed to the ath10k-firmware repository and are now part of ath10k-firmware 2018-04-19. We switched to the upstream board-2.bin, hence the files can be removed here. Keep the ipq-wifi package in case new boards are added. It might take some time till board-2.bins send upstream are merged. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> 
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.

We switched to the upstream board-2.bin, hence the files can be removed
here.

Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
firmware: ath10k-firmware: update to 2018-04-19 2018-04-23T20:07:22+00:00 Sven Eckelmann sven.eckelmann@openmesh.com 2018-04-19T06:59:48+00:00 23894524a57f7d714f2c23aa3475e3c6fe85d7e3 * introduces the BDFs in /lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin for: - 8devices Jalapeno - Asus RT-AC58U - AVM FRITZ!Box 4040 - GL.iNet GL-B1300 - Meraki MR33 - Netgear EX6100v2 - Netgear EX6150v2 - OpenMesh A62 * introduces the BDFs in /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin - OpenMesh A62 * adds new firmware for QCA6174 hw3.0 - firmware-6.bin_RM.4.4.1.c1-00038-QCARMSWP-1 - firmware-6.bin_RM.4.4.1.c1-00041-QCARMSWP-1 * various undocumented BDF updates to: - QCA4019 hw1.0: + bus=ahb,bmi-chip-id=0,bmi-board-id=16 + bus=ahb,bmi-chip-id=0,bmi-board-id=17 + bus=ahb,bmi-chip-id=0,bmi-board-id=19 + bus=ahb,bmi-chip-id=0,bmi-board-id=20 + bus=ahb,bmi-chip-id=0,bmi-board-id=21 + bus=ahb,bmi-chip-id=0,bmi-board-id=29 + bus=ahb,bmi-chip-id=0,bmi-board-id=30 - QCA9888 hw2.0: + bus=pci,bmi-chip-id=0,bmi-board-id=16 + bus=pci,bmi-chip-id=0,bmi-board-id=17 + bus=pci,bmi-chip-id=0,bmi-board-id=18 + bus=pci,bmi-chip-id=0,bmi-board-id=23 + bus=pci,bmi-chip-id=0,bmi-board-id=24 + bus=pci,bmi-chip-id=0,bmi-board-id=25 - QCA9984 hw1.0: + bus=pci,bmi-chip-id=0,bmi-board-id=1 + bus=pci,bmi-chip-id=0,bmi-board-id=3 + bus=pci,bmi-chip-id=0,bmi-board-id=5 + bus=pci,bmi-chip-id=0,bmi-board-id=6 + bus=pci,bmi-chip-id=0,bmi-board-id=7 + bus=pci,bmi-chip-id=0,bmi-board-id=8 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> 
* introduces the BDFs in /lib/firmware/ath10k/QCA4019/hw1.0/board-2.bin
  for:
  - 8devices Jalapeno
  - Asus RT-AC58U
  - AVM FRITZ!Box 4040
  - GL.iNet GL-B1300
  - Meraki MR33
  - Netgear EX6100v2
  - Netgear EX6150v2
  - OpenMesh A62
* introduces the BDFs in /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
  - OpenMesh A62
* adds new firmware for QCA6174 hw3.0
  - firmware-6.bin_RM.4.4.1.c1-00038-QCARMSWP-1
  - firmware-6.bin_RM.4.4.1.c1-00041-QCARMSWP-1
* various undocumented BDF updates to:
  - QCA4019 hw1.0:
    + bus=ahb,bmi-chip-id=0,bmi-board-id=16
    + bus=ahb,bmi-chip-id=0,bmi-board-id=17
    + bus=ahb,bmi-chip-id=0,bmi-board-id=19
    + bus=ahb,bmi-chip-id=0,bmi-board-id=20
    + bus=ahb,bmi-chip-id=0,bmi-board-id=21
    + bus=ahb,bmi-chip-id=0,bmi-board-id=29
    + bus=ahb,bmi-chip-id=0,bmi-board-id=30
  - QCA9888 hw2.0:
    + bus=pci,bmi-chip-id=0,bmi-board-id=16
    + bus=pci,bmi-chip-id=0,bmi-board-id=17
    + bus=pci,bmi-chip-id=0,bmi-board-id=18
    + bus=pci,bmi-chip-id=0,bmi-board-id=23
    + bus=pci,bmi-chip-id=0,bmi-board-id=24
    + bus=pci,bmi-chip-id=0,bmi-board-id=25
  - QCA9984 hw1.0:
    + bus=pci,bmi-chip-id=0,bmi-board-id=1
    + bus=pci,bmi-chip-id=0,bmi-board-id=3
    + bus=pci,bmi-chip-id=0,bmi-board-id=5
    + bus=pci,bmi-chip-id=0,bmi-board-id=6
    + bus=pci,bmi-chip-id=0,bmi-board-id=7
    + bus=pci,bmi-chip-id=0,bmi-board-id=8

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
mac80211: add RedPine RS9113 module support 2018-04-18T21:56:55+00:00 Evgeniy Didin Evgeniy.Didin@synopsys.com 2018-04-04T10:52:24+00:00 36314c12c0df4370de1850b90db4c42c918907cd RedPine RS9113 wireless module requires rsi91x driver to be built and linux-firmware/rsi/rs9113_wlan_qspi.rps to be installed. Also we add patch for successful compilation of rsi91x driver. Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com> Cc: Alexey Brodkin <abrodkin@synopsys.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: John Crispin <john@phrozen.org> 
RedPine RS9113 wireless module requires rsi91x driver to be built
and linux-firmware/rsi/rs9113_wlan_qspi.rps to be installed.
Also we add patch for successful compilation of rsi91x driver.

Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
ath10k-ct: Update firmware 2018-04-13T05:48:19+00:00 Ben Greear greearb@candelatech.com 2018-04-12T18:13:55+00:00 b2bbef7eb451a5abde4e200851e42514ea5a83ac This firmware has only small changes from the last commit, but it does have an important fix for at least some PTK rekey logic. The old firmware would have issues if the driver managed to set a clear key while encryption was 'enabled'. This new firmware for both wave-1 and wave-2 should not be susceptible to this type of bug any more. And remove mesh-bcast IE flag from wave-2, still need more work before we can enable that flag in ath10k-ct firmware it seems. Signed-off-by: Ben Greear <greearb@candelatech.com> 
This firmware has only small changes from the last commit, but
it does have an important fix for at least some PTK rekey logic.

The old firmware would have issues if the driver managed to set
a clear key while encryption was 'enabled'.  This new firmware for
both wave-1 and wave-2 should not be susceptible to this type of
bug any more.

And remove mesh-bcast IE flag from wave-2, still need more work before
we can enable that flag in ath10k-ct firmware it seems.

Signed-off-by: Ben Greear <greearb@candelatech.com>
ipq40xx: unbundle firmware and board file 2018-04-13T05:48:19+00:00 Mathias Kresin dev@kresin.me 2018-04-12T18:48:35+00:00 fb528b1674b221f9d46ab24d1e9ab9ee0f54a66c Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.

Remove the per device selection of the firmware now that it the
firmware is selected by default.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ipq40xx: add support for Netgear EX6100v2/EX6150v2 2018-04-13T05:48:19+00:00 David Bauer mail@david-bauer.net 2018-03-28T22:32:38+00:00 970f1914be3f299fb302ca74a214589397000858 Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net> 
Specifications:
SOC:	Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM:	256 MB Winbond W632GU6KB12J
FLASH:	16 MiB Macronix MX25L12805D
ETH:	Qualcomm QCA8072
WLAN1:  Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2:  Qualcomm Atheros QCA4018 5GHz 802.11n/ac
	1x1 (EX6100)
	2x2 (EX6150)
INPUT:  Power, WPS, reset button
	AP / Range-extender toggle
LED:	Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL:	Header next to QCA8072 chip.
	VCC, TX, RX, GND (Square hole is VCC)
	WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi (Correct MAC-address)
 - 5 GHz WiFi (Correct MAC-address)
 - Factory installation from WebIF
 - Factory installation from tftp
 - OpenWRT sysupgrade (Preserving and non-preserving)
 - LEDs
 - Buttons

Not Working:
 - AP/Extender toggle-switch

Untested:
 - Support on EX6100v2. They share the same GPL-Code and vendor-images.
   The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
   board-blob. I only own a EX6150v2, therefore i am only able to verify
   functionality on this device.

Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.

Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.

Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.

See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html

Signed-off-by: David Bauer <mail@david-bauer.net>
ipq-wifi: Add 8devices Jalapeno 2018-04-13T05:48:19+00:00 Robert Marko robimarko@gmail.com 2018-03-16T17:09:19+00:00 be6e28b516be2701bb734b11fe39d739207e9186 Add custom board-2.bin for 8devices Jalapeno. Upstreaming is in progress. Signed-off-by: Robert Marko <robimarko@gmail.com> 
Add custom board-2.bin for 8devices Jalapeno.
Upstreaming is in progress.

Signed-off-by: Robert Marko <robimarko@gmail.com>
ath10k-ct: Update firmware to latest. 2018-03-31T14:12:33+00:00 Ben Greear greearb@candelatech.com 2018-03-26T22:28:00+00:00 d6939baac22d0c64f02c01de0d822c8c4eea8f69 Wave-1 firmware has a fix for 'addba' not finding the peer. Thanks to Hauke for finding and reporting this. Wave-2 firmware has a fix for leaking a peer multicast key when a monitor device is created. And I re-ordered the '4019' firmware images in the Makefile to match the order of the others. No functional change for that reorder. Signed-off-by: Ben Greear <greearb@candelatech.com> Tested-by: Rosen Penev <rosenp@gmail.com> 
Wave-1 firmware has a fix for 'addba' not finding the peer.  Thanks to Hauke
for finding and reporting this.

Wave-2 firmware has a fix for leaking a peer multicast key when a monitor device
is created.

And I re-ordered the '4019' firmware images in the Makefile to match the order
of the others.  No functional change for that reorder.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Rosen Penev <rosenp@gmail.com>