mtk-20170518/scripts, branch v18.06.1 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker include/feeds.mk: rework generation of opkg distfeeds.conf 2018-07-12T19:26:42+00:00 Matthias Schiffer mschiffer@universe-factory.net 2018-07-09T22:00:01+00:00 514a4b3e1b4e42fa796d1c908259ee9e215a77da Allow enabling/commenting/disabling each feed individually by using a tristate config symbol. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 16035a7dd370671670693af9ae63368ee4dd731f) 
Allow enabling/commenting/disabling each feed individually by using a
tristate config symbol.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 16035a7dd370671670693af9ae63368ee4dd731f)
scripts/feeds: add src-dummy method 2018-07-12T19:26:41+00:00 Matthias Schiffer mschiffer@universe-factory.net 2018-07-09T20:00:27+00:00 a5b9553cf5922262383f7c42ec5e145a86c71624 The src-dummy method does not actually obtain any feed, but it can be used to insert addtional entries into the opkg distfeeds.conf. This is useful to make package feeds available to users without requiring the corresponding source feeds to be available during build. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> (cherry picked from commit 6bdd5d8459cca7ceb93c841cccf61dc7ce830092) 
The src-dummy method does not actually obtain any feed, but it can be used
to insert addtional entries into the opkg distfeeds.conf. This is useful to
make package feeds available to users without requiring the corresponding
source feeds to be available during build.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 6bdd5d8459cca7ceb93c841cccf61dc7ce830092)
build: fix target metadata scan dependencies 2018-07-03T09:20:42+00:00 Felix Fietkau nbd@nbd.name 2018-07-02T12:23:19+00:00 2a7d8cd165be3045727fabd9bbfd53fc84fda675 Move SCAN_DEPS to scan.mk to eliminate redundancy with scripts/feeds Add image/*.mk to SCAN_DEPS for targets to pick up newly added devices Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Move SCAN_DEPS to scan.mk to eliminate redundancy with scripts/feeds
Add image/*.mk to SCAN_DEPS for targets to pick up newly added devices

Signed-off-by: Felix Fietkau <nbd@nbd.name>
env: only use color diffs on terminals 2018-05-05T07:44:43+00:00 Philip Prindeville philipp@redfish-solutions.com 2018-04-10T22:57:06+00:00 e495a050693952956a81847669b8b7888b4cd769 When sending script/env diff's output to a file or pipeline, you don't want escape characters for ANSI color sequences fouling the byte stream. Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com> 
When sending script/env diff's output to a file or pipeline, you
don't want escape characters for ANSI color sequences fouling the
byte stream.

Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
download.pl: Change OpenWrt mirrors to HTTPS. 2018-05-01T09:12:15+00:00 Rosen Penev rosenp@gmail.com 2018-02-20T20:43:01+00:00 1ce846580a638bb8a9f9c2571840be65331be38e These have supported HTTPS for quite a while. I have not seen any obvious breakage. Signed-off-by: Rosen Penev <rosenp@gmail.com> 
These have supported HTTPS for quite a while. I have not seen any obvious breakage.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
download.pl: Change SourceForge address to HTTPS. 2018-05-01T09:12:15+00:00 Rosen Penev rosenp@gmail.com 2018-02-20T20:43:00+00:00 9ea90209f9ef3a786b34995092e830c50a65ddfd SourceForge has supported HTTPS for its downloads for a long time now. I have not been able to see any failures resulting from this change. Signed-off-by: Rosen Penev <rosenp@gmail.com> 
SourceForge has supported HTTPS for its downloads for a long time now.

I have not been able to see any failures resulting from this change.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
scripts/feeds: add support for git feeds with submodules 2018-04-27T13:19:19+00:00 Felix Fietkau nbd@nbd.name 2018-04-25T09:31:48+00:00 41ab276fe4d6a18f7bf875b4727474104fc4e136 Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Signed-off-by: Felix Fietkau <nbd@nbd.name>
scripts: bundle-libraries: fix build on OS X (FS#1493) 2018-04-26T14:06:55+00:00 Jo-Philipp Wich jo@mein.io 2018-04-26T14:04:37+00:00 746c590882b96d5ed4d4115e4bdab4c838af7806 This allegedly fixes compilation of the library bundler preload library on Apple OS X. The resulting executables have not been runtime tested due to a lack of suitable test hardware. Signed-off-by: Jo-Philipp Wich <jo@mein.io> 
This allegedly fixes compilation of the library bundler preload library on
Apple OS X. The resulting executables have not been runtime tested due to a
lack of suitable test hardware.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ipq40xx: add support for OpenMesh A62 2018-04-23T20:07:22+00:00 Sven Eckelmann sven.eckelmann@openmesh.com 2017-08-09T11:52:07+00:00 0b204902075157dbb002ea04f41a5b1a4fbe848c * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> 
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
  - triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + 802.3at POE+
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 18-24V passive POE (mode B)
* powered only via POE

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

The initramfs image can be started using

  setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
  tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
  set fdt_high 0x85000000
  bootm 0x84000000

Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
scripts: add EVA ramboot script 2018-03-18T21:22:38+00:00 Valentin Spreckels Valentin.Spreckels@Informatik.Uni-Oldenburg.DE 2018-03-09T19:17:16+00:00 7a303fe5d135d223d84ee8157aa2c5eebcc4182e Use the EVA bootloader to load a small linux system into the ram and boot it from there: ./scripts/flashing/eva_ramboot.py 192.168.178.1 path/to/initramfs-kernel.bin Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE> Acked-by: John Crispin <john@phrozen.org> [reworded commit message] Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the EVA bootloader to load a small linux system into the ram and boot
it from there:

  ./scripts/flashing/eva_ramboot.py 192.168.178.1 path/to/initramfs-kernel.bin

Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
Acked-by: John Crispin <john@phrozen.org>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>