mtk-20170518/target/linux/ar71xx/files/drivers/mtd, branch master MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ar71xx: fix typo in rb91x nand source 2018-08-24T07:18:13+00:00 Koen Vandeputte koen.vandeputte@ncentric.com 2018-08-24T07:10:29+00:00 6100655c8ce29cd789da8e03b184da2ddb1008f5 Fixes: 3b1ea0996f83 ("ar71xx: fix build error due to bad include") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> 
Fixes: 3b1ea0996f83 ("ar71xx: fix build error due to bad include")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ar71xx: fix build error due to bad include 2018-08-22T11:11:59+00:00 Koen Vandeputte koen.vandeputte@ncentric.com 2018-08-22T11:00:22+00:00 3b1ea0996f83690695e06d11e0214110b6f7201f While "rawnand.h" is available in kernel 4.14, the default for this target is kernel 4.9 in which "nand.h" should be used. Add an extra check to include the correct file depending on kernel version Fixes these build errors: drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory #include <linux/mtd/rawnand.h> ^~~~~~~~~~~~~~~~~~~~~ compilation terminated. Fixes: 318e19ba6755 ("ar71xx: add v4.14 support") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> 
While "rawnand.h" is available in kernel 4.14,
the default for this target is kernel 4.9 in which "nand.h" should be used.

Add an extra check to include the correct file depending on kernel version

Fixes these build errors:

drivers/mtd/nand/ar934x_nfc.c:16:10: fatal error: linux/mtd/rawnand.h: No such file or directory
 #include <linux/mtd/rawnand.h>
          ^~~~~~~~~~~~~~~~~~~~~
compilation terminated.

Fixes: 318e19ba6755 ("ar71xx: add v4.14 support")

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ar71xx: add v4.14 support 2018-08-22T06:09:00+00:00 John Crispin john@phrozen.org 2018-08-09T13:59:41+00:00 318e19ba6755105bb6cc19937d8fff26cbd2cc6f adds v4.14 patches for testing but leaves v4.9 as default for now. Signed-off-by: John Crispin <john@phrozen.org> 
adds v4.14 patches for testing but leaves v4.9 as default for now.

Signed-off-by: John Crispin <john@phrozen.org>
ar71xx: fix mikrotik routerboard nand driver issues with linux 4.9 2017-10-24T11:24:04+00:00 Felix Fietkau nbd@nbd.name 2017-10-24T10:30:48+00:00 7c09fa4a7492ca436f2c94bd9a465b7c5bbeed6f The mtd device is now embedded inside the nand chip data structure Signed-off-by: Felix Fietkau <nbd@nbd.name> 
The mtd device is now embedded inside the nand chip data structure

Signed-off-by: Felix Fietkau <nbd@nbd.name>
ar71xx: Add kernel 4.9 support 2017-10-11T20:32:39+00:00 Hauke Mehrtens hauke@hauke-m.de 2017-10-03T16:02:59+00:00 7bbf4117c6fe4b764d9d7c62fb2bcf6dd93bff2c This add support for kernel 4.9 to the ar71xx target. It was compile tested with the generic, NAND and mikrotik subtarget. Multiple members of the community tested it on their boards and did not report any major problem so far. Especially the NAND part received some changes to adapt to the new kernel APIs. The serial driver hack used for the Arduino Yun was not ported because the kernel changed there a lot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> 
This add support for kernel 4.9 to the ar71xx target.
It was compile tested with the generic, NAND and mikrotik subtarget.
Multiple members of the community tested it on their boards and did not
report any major problem so far.

Especially the NAND part received some changes to adapt to the new
kernel APIs. The serial driver hack used for the Arduino Yun was not
ported because the kernel changed there a lot.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Revert "ar71xx: Add support for Teltonika RUT900" 2017-05-18T13:31:47+00:00 John Crispin john@phrozen.org 2017-05-18T13:31:26+00:00 bad2f9c4dc39ff8a8bdc7ad4bd86f2c068457a5a This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1. pepe2k pointed out that this was not ready to merge Signed-off-by: John Crispin <john@phrozen.org> 
This reverts commit 224e5f5efa22b8a0132522367afd3b22f05d53e1.

pepe2k pointed out that this was not ready to merge

Signed-off-by: John Crispin <john@phrozen.org>
ar71xx: Add support for Teltonika RUT900 2017-05-18T12:47:53+00:00 Steffen Weinreich steve@weinreich.org 2017-04-27T21:59:22+00:00 224e5f5efa22b8a0132522367afd3b22f05d53e1 Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet ports, I/O, RS232, RS485, GPS. The device ist based on a Atheros AR9344 rev 3, Specifications: - 560/450/225 MHz (CPU/DDR/AHB) - 128 MB of RAM - 16 MB of FLASH - Serial Console header on a Card Board edge connector - 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN) - 2.4 GHz Wifi - 2x external, detachable Wifi antennas - LTE Modem Huawei ME909u-521 (Also other Modem seen) - 2x LTE antennas - 1x GPS antenna - 7x LED, 1x button - 1x USB Connector - 1x Serial RS232 - 1x Serial RS485 - 1x MicroSD Card The GPL sources of the device are available at www.teltonika.lt/gpl/ and are based on OpenWRT Barrier Breaker (14.07) Running from tftp: The Router starts into the uboot Webupdater if the Button ist pressed more than 3 seconds, if no Network cable is attached it starts the uboot serial console, from there the router loads the firmware image via tftpboot from 192.168.1.2:firmware.bin (the router has the 192.168.1.1). With bootm the loaded image will be booted. Signed-off-by: Steffen Weinreich <steve@weinreich.org> 
Teltonika RUT900 is a Router with LTE dual SIM, WiFi, 4x Ethernet
ports, I/O, RS232, RS485, GPS.

The device ist based on a Atheros AR9344 rev 3,

Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 128 MB of RAM
- 16 MB of FLASH
- Serial Console header on a Card Board edge connector
- 4x 10/100 Mbps Ethernet (3x LAN, 1x WAN)
- 2.4 GHz Wifi
- 2x external, detachable Wifi antennas
- LTE Modem Huawei ME909u-521 (Also other Modem seen)
- 2x LTE antennas
- 1x GPS antenna
- 7x LED, 1x button
- 1x USB Connector
- 1x Serial RS232
- 1x Serial RS485
- 1x MicroSD Card

The GPL sources of the device are available at www.teltonika.lt/gpl/
and are based on OpenWRT Barrier Breaker (14.07)

Running from tftp:

The Router starts into the uboot Webupdater if the Button ist pressed
more than 3 seconds, if no Network cable is attached it starts the
uboot serial console, from there the router loads the firmware image
via tftpboot from 192.168.1.2:firmware.bin (the router has the
192.168.1.1). With bootm the loaded image will be booted.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
ar71xx: convert mikrotik routerboard support to UBI 2017-01-16T19:40:12+00:00 Felix Fietkau nbd@nbd.name 2017-01-08T13:27:38+00:00 9db9072d6767e5910e01b8962171c89359ab7a14 Remove the wget2nand script, drop the need for manual installation, use sysupgrade instead. There are now two different NAND images, one for 64 MiB flashes, the other for >= 128 MiB Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Remove the wget2nand script, drop the need for manual installation,
use sysupgrade instead.

There are now two different NAND images, one for 64 MiB flashes, the
other for >= 128 MiB

Signed-off-by: Felix Fietkau <nbd@nbd.name>
ar71xx: disable sub-page writes on routerboard nand drivers 2017-01-11T12:10:19+00:00 Felix Fietkau nbd@nbd.name 2017-01-08T12:45:02+00:00 e21cb649a235180563363b8af5ba8296b9ac0baa They seem to fail in tests using UBI, and are not used by yaffs2 Signed-off-by: Felix Fietkau <nbd@nbd.name> 
They seem to fail in tests using UBI, and are not used by yaffs2

Signed-off-by: Felix Fietkau <nbd@nbd.name>
ar71xx: remove a non-upstream spi core patch 2017-01-05T10:09:13+00:00 Felix Fietkau nbd@nbd.name 2016-12-29T00:07:34+00:00 af79fdbe4af32a287798b579141204bda056b8aa - use standard flags instead - remove dead code from the rb4xx spi drivers Signed-off-by: Felix Fietkau <nbd@nbd.name> 
- use standard flags instead
- remove dead code from the rb4xx spi drivers

Signed-off-by: Felix Fietkau <nbd@nbd.name>