mtk-20170518/target/linux/at91/image, branch master

at91: do not build image for at91-q5xr5

2018-08-12T09:34:50+00:00

The kernel image of the at91-q5xr5 is getting too bing now and this is
breaking the build. Remove the image for the at91-q5xr5 from the build
to at least build images for the other devices.

Signed-off-by: Hauke Mehrtens

at91: sama5d4: fix bad mkubifs options

2018-05-13T16:33:47+00:00

Drop the "-x lzo" compression type override from MKUBIFS_OPTS since we
do not support it in mkfs.ubifs. Attempting to use LZO compression results
in "Error: bad compressor name".

The build system also appends an explicit "--compr=zlib" to the mkfs command
line, turning the "-x" flag into a no-op anyway.

Signed-off-by: Jo-Philipp Wich

at91: Add SAMA5D2 PTC EK board

2018-05-05T04:55:22+00:00

Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: reorganize at91 subtargets

2018-05-05T04:55:22+00:00

reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
  1. able to set neon flags to sama5d2 & sama5d4 subtargets.
  2. fix the make clean which removes all the subtargets in bin folder.
  3. able to configure kernel specific to subtarget.
  4. able to set vfpu4 flags to samad3 subtargets.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: sdcard image with ext4 rootfs

2018-05-05T04:55:21+00:00

creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: Add SAMA5D27 SOM1 EK board

2018-05-05T04:55:21+00:00

Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: fix sdcard create image

2018-05-05T04:55:01+00:00

copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: fix build error for wb50n.

2018-04-30T07:01:12+00:00

when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.

Signed-off-by: Sandeep Sheriker Mallikarjun

at91: fix image building with CONFIG_TARGET_MULTI_PROFILE

2018-02-14T14:47:16+00:00

The current image build code has a number of race conditions and interface
contract violations in the custom image build steps:

 - Build/install-zImage, solely used by at91, relies on $(PROFILE_SANITIZED)
   which is not available when building with CONFIG_TARGET_MULTI_PROFILE

 - Build/at91-sdcard, which may run concurrently, creates scratch files at
   fixed locations and manipulates target files directly which can lead
   to file corruption and other unexpected failures

Rename the install-zImage macro to at91-install-zImage and move it to the
at91 image Makefile since this target is the sole user. Also utilize "$@"
as output file name and switch the usage of $(PROFILE_SANITIZED) to
$(DEVICE_NAME) in order to fix naming under multi profile builds.

Fix the at91-sdcard macro to construct scratch file paths relative to "$@",
which is guaranteed to be unique and store the final artifact output in "$@"
as well, instead of inside $(BIN_DIR). The generic image build code takes
care of moving a build steps "$@" output to the final destination in a
concurrency-safe manner.

Finally remove the broken install-zImage from the generic image-commands
Makefile.

Fixes: d7a679a036 ("at91: Install zImage.")
Signed-off-by: Jo-Philipp Wich

at91: create device specific sdcard images

2018-01-11T19:35:33+00:00

Without this patch one sdcard image with the following name is created
for all devices:
openwrt-at91-sama5--sdcard.img.gz
This makes the build system create device specific versions like:
openwrt-at91-sama5-at91-sama5d2_xplained-sdcard.img.gz

Signed-off-by: Hauke Mehrtens