mtk-20170518/target/linux/brcm2708/base-files/lib, branch master

brcm2708: platform.sh: fix tar directory directive

2018-07-07T16:19:39+00:00

BusyBox's `tar` command does not support the `--directory` directive, which
is essentially `-C` in short-form option.
BusyBox's `tar` command supports `-C`.

Signed-off-by: Alexandru Ardelean

brcm2708: move wifi calibration EEPROMs out of base-files

2018-06-14T16:15:33+00:00

Ship EEPROM blobs for specific supported board only and don't have them
lurking around in our source tree but rather download them from
@github/RPi-Distro/firmware-nonfree upstream.

Signed-off-by: Daniel Golle

brcm2708: add RPi3+ wifi calibration data

2018-06-14T11:54:17+00:00

Add files from
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.txt
https://github.com/RPi-Distro/firmware-nonfree/raw/master/brcm/brcmfmac43455-sdio.clm_blob

Signed-off-by: Daniel Golle

brcm2708: Add support for raspberry pi 3 b+.

2018-04-27T07:59:33+00:00

Signed-off-by: Christo Nedev

brcm2708: use x86's upgrade scripts for all rpi targets

2017-12-25T11:19:43+00:00

Advantages:
 - preserves existing partition layout on the sd-card.
   Only the boot and rootfs partition will be overwritten.

Please note that sysupgrade will refuse to upgrade, if the existing
installation  has an incompatible partition layout. Future changes
to the bootfs and/or rootfs partition size will likely cause breakage
to the sysupgrade procedure. In these cases, the ext4-sdcard.img.gz
will have to be written to the sdcard manually.
Please don't forget to backup your configuration in this case.

Signed-off-by: Christian Lamparter

brcm2708: convert to dt-based board-detection

2017-12-25T11:19:41+00:00

Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.

Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.

Signed-off-by: Christian Lamparter

brcm2708: convert to metadata

2017-12-25T11:19:36+00:00

This patch converts all the raspberrypi images to utilize
the common metadata-based image verification.

Note: the CM1 and CM3 currently use the same "rpi-cm"
boardname.

Signed-off-by: Christian Lamparter

brcm2708: restore /boot/config.txt before reboot

2017-10-23T09:50:30+00:00

The Raspberry Pi bootloader reads configuration values from config.txt
in the boot partition. This file allows to specify the amount of memory
to assign to the GPU, the license keys for hardware MPEG-2 and VC-1
decoding, Device Tree parameters and overlays, and lots of other things.

Since sysupgrade only restores the configuration after booting the newly
flashed image, these values will not be active, even if sysupgrade would
save /boot/config.txt. To solve this, add the file to the files to be
backed up, and restore it in platform_copy_config, before reboot.

Signed-off-by: Stijn Tintel

treewide: drop target board_name functions

2017-07-15T21:13:34+00:00

They are not used any longer.

Signed-off-by: Mathias Kresin

treewide: use the generic board_name function

2017-07-15T21:13:34+00:00

Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin