mtk-20170518/target/linux/brcm63xx/base-files/etc, branch master

brcm63xx: initial support for Sky SR102 router

2018-07-16T13:12:08+00:00

The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.

To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
SOC: 	    BCM63168 (BMIPS4350 V8.0 @400MHz)
Flash size: 16 MiB
RAM size:   128 MiB

Heavily based on patch for OpenWRT Chaos Chalmer.
Original patch and more info can be found at:
https://openwrt.org/toh/sky/sr102

Known issues:
 - Wireless and ADSL modem are not working.

Signed-off-by: Andrius Štikonas

brcm63xx: Tune the network configuration for several routers

2018-05-18T06:55:37+00:00

- DGND3700v1: fix port numbers, they're in reverse order
- FaST2704n: there is no WAN port identified as such, only 4 LAN
- AD1018: configure the "FIBRE" port as WAN

Signed-off-by: Daniel Gonzalez Cabanelas

brcm63xx: fix Sercomm AD1018 status led

2017-12-17T11:50:22+00:00

The status led part was missed when changing the board name to *-nor.

Fixes: e12c72bb52eb ("brcm63xx: Add Sercomm AD1018 support")
Reported-by: Daniel Gonzalez Cabanelas 
Signed-off-by: Jonas Gorski

brcm63xx: Add Sercomm AD1018 support

2017-12-16T11:57:05+00:00

Add support for the Sercomm AD1018 router

This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.

Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski

brcm63xx: Add Comtrend AR-5315u support

2017-08-26T10:03:55+00:00

Add support for the Comtrend AR-5315u router

This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski

treewide: use the generic board_name function

2017-07-15T21:13:34+00:00

Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin

brcm63xx: add support for the Actiontec R1000H gateway

2017-06-30T10:12:17+00:00

SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0

Known issues:
 - Unable to detect 53115 switch attached to MDIO. Not supported
 - No support for the cable port

More info on the device and the research can be found at:
http://www.actiontec.com/212.html

Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)

Signed-off-by: Anthony Sepa 
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski

brcm63xx: diag.sh: use common status_led_blink_* functions

2017-03-15T22:15:19+00:00

Signed-off-by: Piotr Dymacz

brcm63xx: CPVA502+: fix userspace support

2017-02-28T12:18:27+00:00

Fix board name typo, fix network configuration and add a led trigger.

Signed-off-by: Daniel Gonzalez Cabanelas

brcm63xx: Add Observa VH4032N support

2017-02-09T21:02:45+00:00

Add support for the Observa Telecom VH4032N router.

This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.

The wifi chip is an onboard Broadcom BCM43222.

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski