mtk-20170518/target/linux/brcm63xx/dts, branch v18.06.0

brcm63xx: drop root parameter from cmdline

2018-02-13T12:17:26+00:00

The root= parameter overrides the automatic rootfs detection by partition
name, so drop it. Fixes boot from flash after renumeration changes of
partitions due to parser changes.

Fixes FS#1350.

Fixes: a27d59bb4274 ("brcm63xx: switch to new partition layout specification")
Signed-off-by: Jonas Gorski

brcm63xx: switch to new partition layout specification

2018-02-11T22:15:05+00:00

Now that we support parsing the expected upstream definition, update
the dts files to it.

Signed-off-by: Jonas Gorski

brcm63xx: register serial through device tree

2017-12-16T11:57:05+00:00

Register serial consoles through device tree instead of through board
data.

Signed-off-by: Jonas Gorski

brcm63xx: add uart nodes

2017-12-16T11:57:05+00:00

Now that we can register uarts through device-tree, add them to the dtsi
files.

Signed-off-by: Jonas Gorski

brcm63xx: Add Sercomm AD1018 support

2017-12-16T11:57:05+00:00

Add support for the Sercomm AD1018 router

This a BCM6328 based board, 128 MB RAM, 128 MiB NAND flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1 USB
host port (not soldered). The board also has an FXS chip (Si32177)
connected via SPI (SS2#), without support in LEDE.

Since NAND flash chips aren't still supported in brcm63xx, the
support is for now added to work only with SPI flash chips. Therefore
hardware modding, soldering a new SPI flash chip, is required
to make the board work with LEDE (tested and working OK).
The flash at dts is intentionally left without partitioning to let
the user choose a NOR chip of any size (8, 16 or 32 MB).

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: renamed ad1018 to ad1018-nor to signify the modification]
Signed-off-by: Jonas Gorski

brcm63xx: Add Comtrend AR-5315u support

2017-08-26T10:03:55+00:00

Add support for the Comtrend AR-5315u router

This a BCM6318 based board, 64 MB RAM, 16 MB SPI flash,
with an onboard BCM43217 wifi, 4 ethernet ports and 1
USB host port

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: refreshed patch]
Signed-off-by: Jonas Gorski

brcm63xx: DTS: fix AV4202N flash layout

2017-07-27T10:12:21+00:00

Fix incorrect offset and size of linux partition.

Fixes: 97b36aca09da ("brcm63xx: add pflash for remaining pflash equipped boards")
Signed-off-by: Paul Wassi 
Signed-off-by: Jonas Gorski

brcm63xx: add support for the Actiontec R1000H gateway

2017-06-30T10:12:17+00:00

SOC: Broadcom BCM6368 (2 * Broadcom BMIPS4350 V3.1 / 400 MHz)
Flash size: 32MB (split 16/16 dual boot)
RAM size: 64MB
Wireless: BCM432x 802.11a/b/g/n(pci)
Ethernet: Broadcom BCM53115
USB: 1 x USB 2.0

Known issues:
 - Unable to detect 53115 switch attached to MDIO. Not supported
 - No support for the cable port

More info on the device and the research can be found at:
http://www.actiontec.com/212.html

Same FCC ID as:
https://wikidevi.com/wiki/Actiontec_V1000H_(Telus)

Signed-off-by: Anthony Sepa 
[jonas.gorski: fix commit subject/message]
Signed-off-by: Jonas Gorski

brcm63xx: probe SPI connected switches through DT

2017-06-10T10:40:38+00:00

Now that we can configure the switches through DT, do so.

Signed-off-by: Jonas Gorski

brcm63xx: switch to hardware led controllers

2017-06-10T10:40:38+00:00

Instead of bit banging SPI to talk to the GPIO chip, use the hardware
led controllers intended for controlling the LEDs.

Signed-off-by: Jonas Gorski