mtk-20170518/target/linux/brcm63xx, branch v17.01.4

brcm63xx: add NULL clock fix send upstream

2017-07-29T07:24:55+00:00

Make the behaviour of clk_get_rate consistent with common clk's
clk_get_rate by accepting NULL clocks as parameter. Some device
drivers rely on this, and will cause an OOPS otherwise.

Fixes: FS#735

Signed-off-by: Mathias Kresin

kernel: update kernel 4.4 to version 4.4.79

2017-07-28T21:49:35+00:00

Signed-off-by: Hauke Mehrtens

kernel: update kernel 4.4 to 4.4.69

2017-05-24T20:47:01+00:00

Bump the 17.01 tree kernel to 4.4.69. Trunk 4.4 and 17.01 4.4 have diverged, talked this
through with jow, he was okay with a clean diff against 17.01 and not a backported trunk
patch.

The following patches were applied upstream:

* 062-[1-6]-MIPS-* series
* 042-0004-mtd-bcm47xxpart-fix-parsing-first-block

Reintroduced lantiq/patches-4.4/0050-MIPS-Lantiq-Fix-cascaded-IRQ-setup, as
it was incorrectly included upstream thus dropped from LEDE, but subsequently
reverted upstream. Thanks to Kevin Darbyshire-Bryant for pointing me to it.

  Compile-tested on: ar71xx, ramips/mt7621, x86/64.

  Run-tested on: ar71xx, ramips/mt7621, x86/64.

Signed-off-by: Stijn Segers

brcm63xx: fix invalid Asmax AR 1004g DTS reference

2017-05-05T17:59:18+00:00

Build profile for Asmax AR 1004g refers to an invalid DTS "rg100a". The
correct DTS for this device is "ar1004g".

Signed-off-by: Marcin Jurkowski

brcm63xx: Add Observa VH4032N support

2017-04-28T15:09:55+00:00

Add support for the Observa Telecom VH4032N router.

This is another BCM6368 router, 128 MB RAM, 32MB flash and 3 USB
host ports.

The wifi chip is an onboard Broadcom BCM43222.

Signed-off-by: Daniel Gonzalez Cabanelas 
[jonas.gorski: use gpio-hog instead of abusing ephy-reset]
Signed-off-by: Jonas Gorski

kernel: update kernel 4.4 to version 4.4.50

2017-02-20T15:02:54+00:00

Signed-off-by: Jo-Philipp Wich

brcm63xx: Neufbox 6: fix switch by probing through DT

2017-02-13T16:51:08+00:00

Probe the switch through DT instead of a platform device. This fixes
probe, as GPIO offsets are now properly accounted for.

Fixes the following issue:

[    0.802953] 8021q: 802.1Q VLAN Support v1.8
[    0.810518] rtl8366_smi: gpio_request failed for 18, err=-517

Signed-off-by: Jonas Gorski

brcm63xx: fix lzma loader for BCM6362

2017-02-10T09:51:09+00:00

BCM6362 and BCM3380 seem to share the same PRID. Disable serial output
for them until we can find a way to tell them apart reliably.

Fixes: 8f3cfe4ba2 ("brcm63xx: lzma-loader: add BCM3380 support")
Signed-off-by: Jonas Gorski

brcm63xx: do a full reset phy cycle

2017-02-10T09:51:09+00:00

Make sure we do a proper reset of the phy, if the phy reset is defined.

Signed-off-by: Jonas Gorski

brcm63xx: fix external interrupts on BCM6318

2017-02-10T09:51:09+00:00

Setting the clear bit for an interrupt seems to cause interrupts to be
deasserted again immediately. So unset the bit for BCM6318 to allow
subsequent interrupts to still work.

Signed-off-by: Jonas Gorski