This reverts commit ec1a695daa7390a6c24e3b28d3956f194cba2cb5. Revert the workaround, the problem was properly fixed in 237454991618e0e8b7ceb8a8a2a43fca12c1a454. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> (cherry picked from commit 5c49fecf72c9c10b1d302b0a9d4db3b4ce3c782c)
commit 33b72b8e0faf7a39faabece584fd6da61cd8f8df "ar8216: adjust ATU flushing in case of link changes" introduced portwise flushing on link down events. Now the ARL table could be in a chaotic state after boot where ar8xxx_sw_get_arl_table looped forever (depending on the entries collected while booting). Fixes FS#384. Signed-off-by: Günther Kelleter <guenther.kelleter@devolo.de> (cherry picked from commit 237454991618e0e8b7ceb8a8a2a43fca12c1a454) Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Running ar8327_get_arl_entry() early after boot leads to MDIO related system lockups on several devices using this driver. Since dumping the ARL table contens is an optional, uncritical feature, simply disable the code for now. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes logic bug(in function netdev_trig_notify) introduced in 0b2991a8ed32b5d9ba0a7c3441a72e1c1a1c4fde commit. Events triggered by different interfaces were stopping work queue so it wasn't working for tx/rx mode. Signed-off-by: Sergey Sergeev <adron@yapic.net>
This fixes hangs in igb that happen if the update call interrupts an already existing dev_get_stats call. In that case the calling CPU deadlocks because it's trying to acquire the same spinlock recursively. Signed-off-by: Felix Fietkau <nbd@nbd.name>
MV88E6352 is used on Linksys WRT3200ACM Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
The priv->vlan_id member is of size AR8X16_MAX_VLANS, not AR8X16_MAX_PORTS, so check for the proper maximum value in order to avoid capping valid VLAN IDs to 7 (AR8X16_MAX_PORTS - 1). Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This patch adds supports for the WNR2000v1 board with 4MB flash, and produces device-specific factory, rootfs, and sysupgrade files for the WNR2000v1. This board is errorneously claimed as supported on the OpenWRT wiki as AP81, but AP81 image would not work because of APT81 image requiring having 8MB of flash, while WNR2000v1 has only 4MB. The image requires the u-boot bootloader to be modified to fuhry's bootloader first. Short specification: - CPU: Atheros AR9132 - 4x 10/100 Mbps Ethernet, 1x WAN 10/100 Mbps - 4 MB of Flash - 32 MB of RAM - UART header (J1) on board - 1x button Factory/Initial flash instructions: - Set up a TFTP server on your local machine. - Download the uImage for ar71xx-generic and the rootfs image for ar71xx-generic-wnr2000 and save in the tftp server root. - Gain serial access to the router via the UART port (telnetenable over the network only won't work!). - Upgrade the u-boot bootloader to fuhry's version by running the script: http://fuhry.com/b/wnr2000/install-repart.sh - When the router restarts, interrupt u-boot and gain access to u-boot command line. - Repartititon the board and flash initial uImage and rootfs as follow. Commands to type in u-boot: # tells u-boot that we have a tftp server on 192.168.1.10 setenv serverip 192.168.1.10 # tells u-boot that the router should take the address 192.168.1.1 setenv ipaddr 192.168.1.1 # erase the region from 0x050000-0x3f0000 erase 0xbf050000 +0x3A0000 # loads sqfs.bin on TFTP server, and put it to memory address 0x81000000 tftpboot 0x81000000 sqfs.bin # it will tell you the length of sqfs.bin in hex, let's say ZZZZZZ # copy bit by bit 0xZZZZZZ bytes from offset 0x050000 cp.b 0x81000000 0xbf050000 0xZZZZZZ # same to the uImage.bin, write it right next to sqfs.bin # again, 0xYYYYYY is the length that tftpboot reports tftpboot 0x81000000 uImage.bin cp.b 0x81000000 0xbf2a0000 0xYYYYYY # We need to tell the kernel what board it is booting into, and where to find the partitions setenv bootargs "board=WNR2000 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd" # Tell u-boot where to find the uImage setenv bootcmd "bootm 0xbf2a0000" # Tell u-boot to save parameters to the u-boot-env partitions saveenv # Reset the board reset Tested on: - WNR2000v1 board. - Initial flash works. Known bugs: - I don't know why factory image doesn't work on initial flash on stock firmware in u-boot recovery mode while it should. - Sysupgrade does not yet work, if you do -f it will mess up your installation (requiring a reinstall of sqfs and uImage). Signed-off-by: Huan Truong <htruong@tnhh.net>
Imported from https://source.codeaurora.org/quic/qsdk/system/openwrt/commit/?h=korg/linux-3.4.y/release/arugula_bb_cs&id=2be4f8a8b205ae1a37db44839864451ebe893e6e Signed-off-by: Pavel Kubelun <be.dissent@gmail.com> Enable flow control of LAN and WAN ports to get better performance. Setup pvid as 0 for all ports during initialisation to avoid confusion during system or switch INIT. Disable PORT MAC before config MAC to avoid it work abnormal. This change is for IR-054144, IR-057315. Change-Id: I345f3dffa59ad3f97150e09692723da12a7b1067 Signed-off-by: Zou Shunxiang <shunxian@codeaurora.org> Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Imported from https://chromium.googlesource.com/chromiumos/third_party/kernel/+/e1aaf7ec008a97311867f0a7d0418e4693fecfd4%5E%21/#F0 Signed-off-by: Pavel Kubelun <be.dissent@gmail.com> CHROMIUM: net: ar8216: address security vulnerabilities in swconfig & ar8216 This patch does the following changes: *address the security vulnerabilities in both swconfig framework and in ar8216 driver (many bound check additions, and turned swconfig structure signed element into unsigned when applicable) *address a couple of whitespaces and indendation issues BUG=chrome-os-partner:33096 TEST=none Change-Id: I94ea78fcce8c1932cc584d1508c6e3b5dfb93ce9 Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org> Reviewed-on: https://chromium-review.googlesource.com/236490 Reviewed-by: Toshi Kikuchi <toshik@chromium.org> Commit-Queue: Toshi Kikuchi <toshik@chromium.org> Tested-by: Toshi Kikuchi <toshik@chromium.org>