Do not assign the CPU port twice, this confuses LuCI and possible other programs relying on topology information in board.json. Ref: https://github.com/openwrt/luci/issues/1086 Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S
D7800") added a trailing TAB char after the backslash which prevents
the assignment of the correct MACs for wifi devices.
Fixes: FS#451
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[reworded commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band. However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading. This patch adds d7800 to ath10k caldata extraction list. I can get two functional wireless bands after making change to it. Signed-off-by: Zhang Jingye <934526987@qq.com>
When running sysupgrade for the first time over the second partition (that still had stock firmware) the rootfs wasn't flashed as there wasn't enough space. This happend because stock also uses UBI, but the volume name wasn't recognised and wasn't deleted before flashing. Signed-off-by: Adrian Panella <ianchi74@outlook.com>
Remove the wifi5g LED from the the d7800, r7500 and r7800. Albeit this GPIO is mentioned in the GPL tarball, it doesn't do anything. The 2.4/5 GHz LEDs are connected to the wifi chips and not be controlled from the the userspace. Use the LEDs names/colours as they are used in the board manuals. Merge redundant LED configurations. Use the phy[0|1]tpt trigger for the wireless LEDs. Remove the workarounds for the not controllable wireless LEDs. Fix spi compatible strings and remove superfluous spi-max-frequency parameters. If there are two power leds, use one for indicating normal operation and one for failsafe/upgrade. Keep the on/off state of the main power led during boot. Use the usb pinmux settings from the nbg6817 gpl sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
Set the pinmux to the values found in the GPL tarballs of the boards. Remove pinmux which are is not used (like nand pinmux for spi flash boards). This allows to use the wan orange led of the C2600 which had a wrong pinmux before. Might fix buttons or leds of other boards as well. Fix the LED color and the ledswitch key code of the C2600. Rename the ledgnr to ledswitch. Add support for indication the boot state using LEDs to the D7800, NBG6817, R7500 and R7500v2. Change GPIO active to readable values in D7800, EA8500, R7500, R7500v2 and R7800. Change gpioexport to gpio pinmux. Add proper "drive strenght" to i2c4_pins and use it for RPM on C2600, D7800, EA8500, R7500, R7500v2. Remove pcie pinmux from D7800. Move pinctrl to correct place in NBG6817 and R7800. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>