mtk-20170518/target/linux/ipq806x/image, branch v17.01.6 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ipq806x: nbg6817: add kmod-fs-ext4 to device packages 2017-11-03T21:59:19+00:00 Stefan Lippers-Hollmann s.l-h@gmx.de 2017-10-19T19:40:26+00:00 2aff2add3116906b666da69bfff42a7aeeaee080 The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split into the readonly squashfs and ext4 for the overlay. This adds the required package to the device packages to allow mounting the overlay by default. /dev/root on /rom type squashfs (ro,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,noatime) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime) tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime) /dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered) overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work) tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000) debugfs on /sys/kernel/debug type debugfs (rw,noatime) mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect) Before this commit, the ext4 based overlayfs could not be mounted, which left only the tmpfs based/ volatile emergency overlay in place. Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> 
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.

/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)

Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile  emergency overlay in place.

Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768

Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
ipq806x: fix Netgear X4 R7500 ath10k firmware selection 2017-05-27T12:23:14+00:00 Thomas Reifferscheid thomas@reifferscheid.org 2017-03-17T13:01:34+00:00 20198f7330f5b687f1e5fdfd2b30934f89d51e13 Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches the ath10k chipset Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org> 
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset

Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
treewide: select ath10k firmware explicit 2017-05-27T12:23:07+00:00 Mathias Kresin dev@kresin.me 2017-03-17T18:36:06+00:00 784ceba269c17af7eb2e6120930cf3ecce27445e Do not rely on the default firmware selected by ath10k. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Do not rely on the default firmware selected by ath10k.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ipq806x: add support for TP-Link Archer VR2600v 2016-11-24T21:37:40+00:00 Sebastian Quilitz zeraphim@x-pantion.de 2016-11-23T17:51:15+00:00 ae79c41286f0d9a97f2641450240ecac5465677d This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de> 
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.

It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.

To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.

Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
ipq806x: append metadata to images 2016-11-19T10:24:10+00:00 Felix Fietkau nbd@nbd.name 2016-11-14T16:32:04+00:00 9d6d7d9a0e1f8e516537d80c222ce8f787070280 Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ipq806x: fix zyxel image build error 2016-11-04T12:06:35+00:00 Felix Fietkau nbd@nbd.name 2016-11-04T11:57:16+00:00 36166661268446b49499e89dc1364bc52ad133c2 Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ipq806x/nbg6817: add support for ZyXEL NBG6817 2016-10-26T10:37:46+00:00 André Valentin avalentin@marcant.net 2016-10-25T06:40:34+00:00 a0ed7af6c62bb8972ce7509ac76d0a648b291dd6 CPU: 2x1.8GHz ARM, RAM: 512MiB Storage: 4MiB serial Flash, 3.9GiB MMC NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin to device. Then run: cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4 cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5 reboot -f For debugging serial console is easily visible on board, no soldering needed. Signed-off-by: André Valentin <avalentin@marcant.net> 
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
ipq806x: add back end-of-UBI marker for a few factory images (FS#228) 2016-10-18T07:30:57+00:00 Felix Fietkau nbd@nbd.name 2016-10-18T07:29:50+00:00 a92f57599cea2f1cd3db88b49031b2de1eb3859e Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Signed-off-by: Felix Fietkau <nbd@nbd.name>
image: add KERNEL_SIZE to the default device vars 2016-09-13T17:36:41+00:00 Mathias Kresin dev@kresin.me 2016-09-13T17:23:52+00:00 1cd0a4c688f02918cb96ff7f5f21cddc281d4f2c This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes the underlying issue. 
This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes
the underlying issue.
ramips: improve Linksys EA8500 build code 2016-09-11T17:40:45+00:00 Mathias Kresin dev@kresin.me 2016-09-11T15:46:09+00:00 c7d5bc8197609a62f03f3f6b3d665ae73bd1072b Use of the kernel size variable. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use of the kernel size variable.

Signed-off-by: Mathias Kresin <dev@kresin.me>