Refreshed all patches.

Removed upstreamed patches:
- 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch

Compile-tested on: cns3xxx, imx6
Runtime-tested on: cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>

- fix single spaces hidden by a tab
- replace indentation with spaces by tabs
- make empty lines empty
- drop trailing whitespace
- drop unnecessary blank lines

Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Wassi <p.wassi@gmx.at>

Indicate a (sys)upgrade via leds as well. It brings the lantiq diag.sh
script en par with the other implementations using devicetree aliases
to define multiple leds for boot status indication.

By default, use the boot finished led to indicate an upgrade for now.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Without this patch you will get an error "gpio-export probe deferral
not supported" when you try to export i2c expander gpio pins.

gpio-export is probed long before i2c-bus and i2c expander are created
and it doesn't retry it so none pins are exported.

Signed-off-by: René van Dorst <opensource@vdorst.com>
apply the change to all instances of the gpio exports patch
Signed-off-by: Mathias Kresin <dev@kresin.me>

The FritzBox 7312 is also known as 1&1 WLAN-MODEM. The device is almost
the same as FB7330, but only one ETH-Port and no USB.

Hardware
SoC: Lantiq Xway ARX188 PSB 50812 EL
RAM: 64MB DDR1 (Zentel A4S12D40FTP-G5)
Ethernet: Atheros 8030
Wireless: Atheros AR9227 b/g/n 2x2
DSL: Lantiq ADSL2+
DECT: Dialog SC14441
Buttons: WiFi, DECT
LEDs: Power/DSL, Fon, DECT, WLAN, Info

LEDs
Power: GPIO#44 (active low)
Internet: GPIO#47 (active low)
DECT: GPIO#38 (active low)
WLAN: GPIO#37 (active low)
Info: GPIO#35 (active low)

The Fon LED is labeled as internet in avm gpl sources.

Buttons
WLAN: GPIO#1 (active low)
DECT: GPIO#2 (active low)

Phy
GPIO#03: 25 MHz
GPIO#34: Reset (active low)
GPIO#39: Int
GPIO#42: MII MDIO
GPIO#43: MII MDC

PCIe
GPIO#21: reset (active low)

Installation:

To install OpenWrt via Eva bootloader, within the first seconds after
power on a ftp connection need to be established to the FRITZ!Box at
192.168.178.1 and the the following ftp commands need to be run:

  ftp> quote USER adam2
  ftp> quote PASS adam2
  ftp> binary
  ftp> debug
  ftp> passive
  ftp> quote MEDIA FLSH
  ftp> put /path/to/openwrt-lantiq-xway-avm_fritz7312-squashfs-sysupgrade.bin mtd1
  ftp> quote REBOOT

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>

Use of_mdiobus_register() to pass the ethernet phy node to the phy
drivers. This is needed for the at8030 phy driver which needs to know
the GPIO which is connected to the ar8030 reset pin.

This driver expects a child in gsw/etop node named "mdio-bus", which has
the ethernet phys defined:

&gsw {
	phy-mode = "rmii";
	phy-handle = <&phy0>;
	mtd-mac-address = <&ath9k_cal 0xa91>;
	mtd-mac-address-increment = <(-2)>;

	mdio-bus {
		#address-cells = <1>;
		#size-cells = <0>;
		reg = <0>;

		phy0: ethernet-phy@0 {
			reg = <0>;
			reset-gpios = <&gpio 34 GPIO_ACTIVE_LOW>;
		};
	};
};

Fallback to mdiobus_register() if no mdio-bus child node exists. This
way we don't need to touch all xway dts files, for which we don't know
the actual address on the mdio bus.

Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>

Add a new config option to allow to select the default compile
optimization level for the kernel.

Select the optimization for size by default if the small_flash feature is
set. Otherwise "Optimize for performance" is set.

Add the small_flash feature flag to all (sub)targets which had the
optimization for size in their default kernel config.

Remove CC_OPTIMIZE_FOR_* symbols from all kernel configs to apply the new
setting.

Exceptions to the above are:

  - lantiq, where the optimization for size is only required for the
    xway_legacy subtarget but was set for the whole target
  - mediatek, ramips/mt7620 & ramips/mt76x8 where boards should have
    plenty of space and an optimization for size doesn't make much sense
  - rb532, which has 128MByte flash

Signed-off-by: Mathias Kresin <dev@kresin.me>

Increase the available flash memory size in AVM Fritz!Box 3370 by
incorporating the unused extra partitions located after the ubi partition.

Note that users upgrading from a previous OpenWRT version need to
re-install from the boot loader to pick up the new partition layout.

Available flash space for rootfs+overlay increases from 48MB to 124MB.

Reverting to the OEM firmware is still possible (via the recovery utility
provided by AVM) as the OEM firmware appears to reformat the config and
nand-filesystem partitions upon first boot if necessary. The
reserved-kernel and reserved-filesystem partitions are overwritten by the
OEM firmware when installing an update, so their contents do not matter.

Boot loader and device-specific information (MAC addresses, calibration
data, etc.) are not located in NAND flash and remain unharmed by this
changed.

Tested with OEM firmware 06.54 on device with HWRevision 5 and Micron
flash chip.

Signed-off-by: Michael Kuron <m.kuron@gmx.de>

To keep the status of a LED connected to the stp during boot, the get
callback is required. If the callback is missing and the LED default
state is set to keep in the devicetree, the gpio led driver errors out
during load.

Fixes: FS#1620

Signed-off-by: Mathias Kresin <dev@kresin.me>

Check if the GPIO is valid (or set at all). If no GPIO is set in the
devicetree, a gpiolib related kernel warning + stacktrace is shown during
boot and gpio-export reports GPIOs as exported albeit none really is.

Signed-off-by: Mathias Kresin <dev@kresin.me>