mtk-20170518/target/linux/layerscape/64b, branch master MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker layerscape: rename subtargets and update makefile files 2017-10-07T21:13:22+00:00 Yangbo Lu yangbo.lu@nxp.com 2017-06-29T03:19:07+00:00 806624add541bd828516a58aab20ae19ae9e431f Rename subtargets 32b/64b with armv8_32b/armv8_64b which are more proper, and update makefile files. There also will be other subtargets added in the future, like armv7. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> 
Rename subtargets 32b/64b with armv8_32b/armv8_64b which are
more proper, and update makefile files. There also will be other
subtargets added in the future, like armv7.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
layerscape: do not add custom CFLAGS. 2017-08-26T10:36:02+00:00 Hauke Mehrtens hauke@hauke-m.de 2017-07-15T20:52:52+00:00 a5d26d7fad1909bafbb6cec52664c3b684a0220c The selected CFLAGS are already set by default. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> 
The selected CFLAGS are already set by default.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
layerscape: add 64b/32b target for ls1046ardb device 2016-12-12T08:57:40+00:00 Yutang Jiang yutang.jiang@nxp.com 2016-12-07T16:07:42+00:00 ad907e1c03a3a1a236f4836cee085d085f280c8d Add support for NXP layerscape ls1046ardb 64b/32b Dev board. LS1046ARDB Specification: ------------------------- Memory subsystem: * 8GByte DDR4 SDRAM (64bit bus) * 512 Mbyte NAND flash * Two 64 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card * On-board 4G eMMC Ethernet: * Two XFI 10G ports * Two SGMII ports * Two RGMII ports PCIe: * PCIe1 (SerDes2 Lane0) to miniPCIe slot * PCIe2 (SerDes2 Lane1) to x2 PCIe slot * PCIe3 (SerDes2 Lane2) to x4 PCIe slot * USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port * UART: supports two UARTs up to 115200 bps for console Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com> 
Add support for NXP layerscape ls1046ardb 64b/32b Dev board.

LS1046ARDB Specification:
-------------------------
Memory subsystem:
* 8GByte DDR4 SDRAM (64bit bus)
* 512 Mbyte NAND flash
* Two 64 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
* On-board 4G eMMC
Ethernet:
* Two XFI 10G ports
* Two SGMII ports
* Two RGMII ports
PCIe:
* PCIe1 (SerDes2 Lane0) to miniPCIe slot
* PCIe2 (SerDes2 Lane1) to x2 PCIe slot
* PCIe3 (SerDes2 Lane2) to x4 PCIe slot

* USB 3.0: one super speed USB 3.0 type A port, one Micro-AB port
* UART: supports two UARTs up to 115200 bps for console

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
layerscape: add 64b/32b target for ls1012ardb device 2016-10-31T16:00:10+00:00 Yutang Jiang yutang.jiang@nxp.com 2016-10-28T16:18:23+00:00 15a14cf1665ef3d8b5c77cce69b52d131340e3b3 The QorIQ LS1012A processor, optimized for battery-backed or USB-powered, integrates a single ARM Cortex-A53 core with a hardware packet forwarding engine and high-speed interfaces to deliver line-rate networking performance. QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance development platform, with a complete debugging environment. The LS1012ARDB board supports the QorIQ LS1012A processor and is optimized to support the high-bandwidth DDR3L memory and a full complement of high-speed SerDes ports. LEDE/OPENWRT will auto strip executable program file while make. So we need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network fiemware be destroyed, then run make to build ls1012ardb firmware. The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message. This issue have noticed the IP owner for investigate, hope he can solve it earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4" bootargs. Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com> 
The QorIQ LS1012A processor, optimized for battery-backed or
USB-powered, integrates a single ARM Cortex-A53 core with a hardware
packet forwarding engine and high-speed interfaces to deliver
line-rate networking performance.
QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance
development platform, with a complete debugging environment.
The LS1012ARDB board supports the QorIQ LS1012A processor and is
optimized to support the high-bandwidth DDR3L memory and
a full complement of high-speed SerDes ports.

LEDE/OPENWRT will auto strip executable program file while make. So we
need select CONFIG_NO_STRIP=y while make menuconfig to avoid the ppfe network
fiemware be destroyed, then run make to build ls1012ardb firmware.

The fsl-quadspi flash with jffs2 fs is unstable and arise some failed message.
This issue have noticed the IP owner for investigate, hope he can solve it
earlier. So the ls1012ardb now also provide a xx-firmware.ext4.bin as default
firmware, and the uboot bootcmd will run wrtboot_ext4rfs for "rootfstype=ext4"
bootargs.

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>
layerscape: add 64b/32b target for ls1043ardb device 2016-10-31T16:00:10+00:00 Yutang Jiang yutang.jiang@nxp.com 2016-10-28T16:14:32+00:00 c6c731fe311f7da42777ffd31804a4f6aa3f8e19 Add support for NXP layerscape ls1043ardb 64b/32b Dev board. LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores. ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC, I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc. 64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from NXP QorIQ SDK release. All of 4.4 kernel patches porting from SDK release or upstream. QorIQ SDK ISOs can be downloaded from this location: http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com> 
Add support for NXP layerscape ls1043ardb 64b/32b Dev board.

LS1043a is an SoC with 4x64-bit up to 1.6 GHz ARMv8 A53 cores.
ls1043ardb support features as: 2GB DDR4, 128MB NOR/512MB NAND, USB3.0, eSDHC,
I2C, GPIO, PCIe/Mini-PCIe, 6x1G/1x10G network port, etc.

64b/32b ls1043ardb target is using 4.4 kernel, and rcw/u-boot/fman images from
NXP QorIQ SDK release.

All of 4.4 kernel patches porting from SDK release or upstream.

QorIQ SDK ISOs can be downloaded from this location:
http://www.nxp.com/products/software-and-tools/run-time-software/linux-sdk/linux-sdk-for-qoriq-processors:SDKLINUX

Signed-off-by: Yutang Jiang <yutang.jiang@nxp.com>