mtk-20170518/target/linux/layerscape/image, branch master

layerscape: add Traverse LS1043-S support

2018-07-30T08:53:57+00:00

The Traverse LS1043-S board is a router board based on
NXP/Freescale's LS1043 SoC, with 4x1GBase-T, 1 SFP and 1 SFP+,
as well as miniPCIe and M.2 LTE.

Unlike the Layerscape reference boards, the LS1043-S board has
NAND flash and uses the mainline U-Boot.

This patch implements support for the LS1043-S board, as well as
the earlier LS1043-V board. It is our intention that all boards
in this family (LS1043-S and later, Five64) will boot the same binary.

Not included in this patchset are the hwmon drivers not in the kernel
(emc1704,pac1934) or the bootloader.

Signed-off-by: Mathew McBride

layerscape: add multiple-configuration generator for FIT images

2018-07-30T08:53:57+00:00

This is required for the Traverse LS1043 family, we generate a FIT image
that works on all boards across the family. This is done by creating
multiple configurations that select the right DTB for the board.

The bootloader on these boards is configured to boot like this:
bootm $kernel_load#ls1043s
bootm $kernel_load#ls1043v

This is based on earlier work by Jason Wu for Zynq:
https://lists.openwrt.org/pipermail/openwrt-devel/2016-March/040460.html

Modified to add FDT load addresses and multiple configurations with DTB.

Signed-off-by: Mathew McBride

layerscape: support ubifs rootfs

2018-02-13T09:01:51+00:00

Some layerscape devices (ls1012ardb/ls1012afrdm/ls1046ardb/ls1088ardb)
were using ext4 rootfs because there were issues using squashfs.
This patch is to drop using ext4 rootfs and use ubifs rootfs instead
which is more proper for SPI-NOR flash.

Signed-off-by: Yangbo Lu

layerscape: add ls1012afrdm device support

2017-11-10T22:00:49+00:00

The QorIQ FRDM-LS1012A Board is an ultra-low-cost
development platform for QorIQ LS1012A Series Network
Processors built on ARM Cortex-A53 processor.

Signed-off-by: Yangbo Lu

layerscape: enlarge ext4 rootfs size to 30MB

2017-11-10T22:00:49+00:00

This patch is to enlarge ext4 rootfs size to 30MB.

Signed-off-by: Yangbo Lu

layerscape: add ppa firmware package

2017-11-10T22:00:49+00:00

This patch is to add PPA (The Primary Protected Application)
package and also enable it for all layerscape devices.
LSDK github provides ppa source code git tree, but it
only could be compiled with 64-bit toolchain. For 32-bit
devices, there was no method to use it.
https://github.com/qoriq-open-source/ppa-generic

This patch is to directly use a private ppa binary tree for
both 32-bit and 64-bit devices.

Signed-off-by: Yangbo Lu

layerscape: support LSDK ppfe

2017-11-10T22:00:49+00:00

This patch is to use ppfe git tree on LSDK github
instead of private git tree, and support the latest
ppfe on ls1012ardb.

Signed-off-by: Yangbo Lu

layerscape: support all-in-one firmware for ls1088ardb/ls2088ardb

2017-11-10T22:00:47+00:00

Suppport all-in-one firmware for ls1088ardb/ls2088ardb by
integrating u-boot/rcw/mc/dpl/restool.

Signed-off-by: Yangbo Lu

layerscape: only support 64-bit for ls1088ardb/ls2088ardb

2017-10-12T21:40:27+00:00

This is no requirement and plan to support 32-bit for ls1088ardb
and ls2088ardb. Current 32-bit firmware for them couldn't work,
so only keep 64-bit support for these two boards in menuconfig.

Signed-off-by: Yangbo Lu

layerscape: select sdk dts for ls1043ardb/ls1046ardb

2017-10-07T21:13:23+00:00

ls1043ardb/ls1046ardb should use sdk dts. This patch is
to fix this.

Signed-off-by: Yangbo Lu