mtk-20170518/target/linux/mpc85xx/base-files/lib/preinit, branch master

mpc85xx: use the generic board detect

2017-10-25T07:22:13+00:00

Use the values populated by the generic board detect function. The
first compatible from the device tree source file will be the board
name in userspace. The model property from the device tree source file
will be the model name.

Change the board name where used in the userspace and drop the target
specific board detect, to use the generic one.

Signed-off-by: Mathias Kresin

mpc85xx: update HiveAP-330 dts

2017-10-25T07:22:08+00:00

initramfs is not the proper name for this, as it stores a boot ramdisk
and not a filesystem. Update the name to reflect it's usage correctly.

If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all.
Drop them from the device tree source file to not cause confusion.

Remove the noinitrd bootarg. Due to the empty ramdisk this parameter
isn't required any longer:

  [    0.000000] Initrd not found or empty - disabling initrd

Use the LEDE mtd-mac-address* device tree properties to set the interfaces
MAC-Addresses.

Signed-off-by: Chris Blake 
Signed-off-by: Mathias Kresin

mpc85xx: Add Aerohive HiveAP-330 Access Point

2017-10-13T23:23:47+00:00

The following adds the Aerohive HiveAP-330 Access Point to LEDE under
the mpc85xx/p1020 subtarget.

Hardware:
- SoC: Freescale P1020NSE2DFB
- NAND: Intel JS28F512M29EWH 64MB
- Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- 5.0GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- Eth2: Atheros AR8035-A
- TPM: Atmel AT97SC3204
- LED Driver: TI LP5521

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
    dhcp;
    tftpboot 0x1000000 192.168.1.101:lede-
mpc85xx-p1020-hiveap-330-initramfs.zImage;
    tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt;
    bootm 0x1000000 - 0x6000000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NAND.
    sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img

Signed-off-by: Chris Blake

treewide: populate boardname and model earlier

2017-07-15T21:13:34+00:00

For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin

base-files: input/button drivers get loaded before preinit by procd

2013-06-21T16:53:47+00:00

Signed-off-by: John Crispin 

SVN-Revision: 37000

mpc85xx: set preinit interface to eth0 by default

2013-04-12T18:30:25+00:00

This makes the WDR4900 accessible via ethernet in
failsafe mode.

Signed-off-by: Gabor Juhos 

SVN-Revision: 36322

mpc85xx: add user-space support for the TL-WDR4900 v1

2013-02-21T19:20:34+00:00

Signed-off-by: Gabor Juhos 

SVN-Revision: 35733

mpc85xx: add input drivers to default packages, and load those during preinit

2013-02-16T17:13:38+00:00

Signed-off-by: Gabor Juhos 

SVN-Revision: 35626