The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the
definition for the related P1010 SoC.  However, the P1040 lacks the
CAAM/SEC4 hardware crypto accelerator which the P1010 device tree
defines.  If left defined, this causes the CAAM drivers (if present) to
attempt to use the non-existent device, making various crypto-related
operations (e.g. macsec and ipsec) fail.

This commit overrides the incorrect dt node definition in the included
file.

See also:
 - https://bugs.openwrt.org/index.php?do=details&task_id=1262
 - https://community.nxp.com/thread/338432#comment-474107

Signed-off-by: Tim Small <tim@seoss.co.uk>

Use the vendor as it is listed in vendor.txt. Use a standard lower case
compatible string.

Signed-off-by: Mathias Kresin <dev@kresin.me>

initramfs is not the proper name for this, as it stores a boot ramdisk
and not a filesystem. Update the name to reflect it's usage correctly.

If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all.
Drop them from the device tree source file to not cause confusion.

Remove the noinitrd bootarg. Due to the empty ramdisk this parameter
isn't required any longer:

  [    0.000000] Initrd not found or empty - disabling initrd

Use the LEDE mtd-mac-address* device tree properties to set the interfaces
MAC-Addresses.

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>

The following adds the Aerohive HiveAP-330 Access Point to LEDE under
the mpc85xx/p1020 subtarget.

Hardware:
- SoC: Freescale P1020NSE2DFB
- NAND: Intel JS28F512M29EWH 64MB
- Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- 5.0GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- Eth2: Atheros AR8035-A
- TPM: Atmel AT97SC3204
- LED Driver: TI LP5521

Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
    dhcp;
    tftpboot 0x1000000 192.168.1.101:lede-
mpc85xx-p1020-hiveap-330-initramfs.zImage;
    tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt;
    bootm 0x1000000 - 0x6000000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NAND.
    sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img

Signed-off-by: Chris Blake <chrisrblake93@gmail.com>

Since commit:
http://github.com/torvalds/linux/commit/7120438e5d82f445acbfe131a1b58eab7e83fa33

Seems that fsl_rstcr_restart() has been converted
to a reset handler and dropped as hook/callback.

Apply the same to the `tl_wdr4900_v1` target.

Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>

since linux 3.19 the address of the gpio-controller changed

Signed-off-by: Alexander Couzens <lynxis@fe80.eu>

SVN-Revision: 48794

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 48645

PTP requires at least one timer to be 1PPS so describe it.
For testing, load kernel module gianfar_ptp and use ptp4l
from linuxptp.

Copied from FSL P1010RDB reference design.

Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>

SVN-Revision: 48275

Signed-off-by: Felix Fietkau <nbd@openwrt.org>

SVN-Revision: 47691

This patch adds the RFKill GPIO control switch and enables another GPIO to
control power supply to USB Ports by emulating an LED GPIO for WDR4900v1.

Signed-off-by: Guo Wei Lim <alphasparc@gmail.com>

SVN-Revision: 46279