mtk-20170518/target/linux/oxnas/base-files/lib/preinit, branch master

oxnas: bring in new oxnas target

2018-06-01T13:45:06+00:00

Reboot the oxnas target based on Linux 4.14 by rebasing our support on
top of the now-existing upstream kernel support.
This commit brings oxnas support to the level of v4.17 having upstream
drivers for Ethernet, Serial and NAND flash.
Botch up OpenWrt's local drivers for EHCI, SATA and PCIe based on the
new platform code and device-tree.
Re-introduce base-files from old oxnas target which works for now but
needs further clean-up towards generic board support.

Functional issues:
 * PCIe won't come up (hence no USB3 on Shuttle KD20)
 * I2C bus of Akitio myCloud device is likely not to work (missing
   debounce support in new pinctrl driver)

Code-style issues:
 * plla/pllb needs further cleanup -- currently their users or writing
   into the syscon regmap after acquireling the clk instead of using
   defined clk_*_*() functions to setup multipliers and dividors.
 * PCIe phy needs its own little driver.
 * SATA driver is a monster and should be split into an mfd having
   a raidctrl regmap, sata controller, sata ports and sata phy.

Tested on MitraStar STG-212 aka. Medion Akoya MD86xxx and Shuttle KD20.

Signed-off-by: Daniel Golle

oxnas: kill old oxnas target

2018-06-01T13:45:06+00:00

Signed-off-by: Daniel Golle

treewide: populate boardname and model earlier

2017-07-15T21:13:34+00:00

For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.

Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.

Signed-off-by: Mathias Kresin

oxnas: set preinit interface in /etc/board.d/02_network

2016-08-19T15:53:50+00:00

Signed-off-by: Daniel Golle

oxnas: set preinit network interface

2016-08-11T15:16:03+00:00

set network interface for failsafe mode to eth0 for all boards

Signed-off-by: Daniel Golle

add new target 'oxnas'

2014-11-26T09:00:08+00:00

This is the oxnas target previously developed at
http://gitorious.org/openwrt-oxnas
Basically, this consolidates the changes and addtionas from
http://github.org/kref/linux-oxnas
into a new OpenWrt hardware target 'oxnas' adding support for
 PLX Technology NAS7820/NAS7821/NAS7825/...
formally known as
 Oxford Semiconductor OXE810SE/OXE815/OX820/...

For now there are 4 supported boards:
Cloud Engines Pogoplug V3 (without PCIe)
 fully supported

Cloud Engines Pogoplug Pro (with PCIe)
 fully supported

MitraStar STG-212
 aka ZyXEL NSA-212,
 aka Medion Akoya P89625 / P89636 / P89626 / P89630,
 aka Medion MD 86407 / MD 86805 / MD 86517 / MD 86587
 fully supported, see http://wiki.openwrt.org/toh/medion/md86587

Shuttle KD-20
 partially supported (S-ATA driver lacks support for 2nd port)

Signed-off-by: Daniel Golle 

SVN-Revision: 43388