mtk-20170518/target/linux/ramips/base-files/etc/hotplug.d/firmware, branch master MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: add support for D-Link DWR-118-A2 2018-08-15T05:42:36+00:00 Cezary Jackiewicz cezary@eko.one.pl 2018-04-19T17:34:22+00:00 37af596593b0e84d0a076ab8f173066e3d7bc810 The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> 
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- GELAN not working
- flash is very slow

The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
ramips: add support for DLINK DWR-921-C1 2018-04-04T06:42:35+00:00 Giuseppe Lippolis giu.lippolis@gmail.com 2018-03-10T09:34:38+00:00 6525bffc0a7ee6fabfe331a4d9e3eeabdd3516ae The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the MT7620N SoC. Specification: * MediaTek MT7620N (580 Mhz) * 64 MB of RAM * 16 MB of FLASH * 802.11bgn radio * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) * 2x external, detachable (LTE) antennas * UART header on PCB (57600 8n1) * 6x LED (GPIO-controlled) * 1x bi-color Signal Strength LED (GPIO-controlled) * 2x button * JBOOT bootloader The status led has been assigned to the dwr-921-c1:green:sigstrength (lte signal strength) led. At the end of the boot it is switched off and is available for lte operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com> 
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui.

How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
    blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
    curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
ramips: add support for D-Link DWR-116-A1/2 2018-03-18T21:22:38+00:00 Pawel Dembicki paweldembicki@gmail.com 2018-01-20T08:27:03+00:00 a5bd8de0bd80b83e43ce90ddc6623890344ad33d The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC. Specification: MediaTek MT7620N (580 Mhz) 32 MB of RAM 8 MB of FLASH 802.11bgn radio 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN) 2x external, non-detachable antennas UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1) 6x LED (GPIO-controlled), 2x button JBOOT bootloader Known issues: WAN LED is drived by uartl tx pin. I decide to use this pin as uartlite tx pin. Installation: Apply factory image via http web-gui. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> 
The DWR-116-A1/2 Wireless Router is based on the MT7620N SoC.

Specification:

  MediaTek MT7620N (580 Mhz)
  32 MB of RAM
  8 MB of FLASH
  802.11bgn radio
  5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  2x external, non-detachable antennas
  UART (J1 in A1, JP1 in A2) header on PCB (57600 8n1)
  6x LED (GPIO-controlled), 2x button
  JBOOT bootloader

Known issues:
WAN LED is drived by uartl tx pin. I decide to use this pin as
uartlite tx pin.

Installation:
Apply factory image via http web-gui.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
treewide: use the generic board_name function 2017-07-15T21:13:34+00:00 Mathias Kresin dev@kresin.me 2017-05-12T20:36:07+00:00 f12a32630ff52b5e13397f64e9fb31708e97fb60 Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the generic function instead ot the target specific ones.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use the ralink,mtd-eeprom device tree property 2016-11-09T19:22:59+00:00 Mathias Kresin dev@kresin.me 2016-11-07T21:02:20+00:00 d8dd207ea6f299cfcaef4899f1cade375e694dd5 Use the ralink,mtd-eeprom instead of invoking the userspace firmware loader. Set the label and compatible string according to the the PCI binding documentation. Use the wifi@0,0 label and the pci0,0 compatible string in case the PCI vendor and device id is unknown. It should work anyway since the compatible string isn't evaluated (yet). This commit might fixes the PCIe wireless for the Buffalo WHR-600D. This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug script but never had the correct eeprom name set to trigger the firmware from flash extraction. Use the usual eeprom for the soc wmac of the Dovado Tiny AC. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the ralink,mtd-eeprom instead of invoking the userspace firmware
loader.

Set the label and compatible string according to the the PCI binding
documentation.

Use the wifi@0,0 label and the pci0,0 compatible string in case the
PCI vendor and device id is unknown. It should work anyway since the
compatible string isn't evaluated (yet).

This commit might fixes the PCIe wireless for the Buffalo WHR-600D.
This board was mentioned in the board 10-rt2x00-eeprom firmware hotplug
script but never had the correct eeprom name set to trigger the
firmware from flash extraction.

Use the usual eeprom for the soc wmac of the Dovado Tiny AC.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: do not "local" variables outside of a function 2016-09-23T23:17:18+00:00 Martin Blumenstingl martin.blumenstingl@googlemail.com 2016-09-23T22:07:24+00:00 d72e838429cbe7638b383b99bf16d97a63f80837 Older busybox versions allowed using the local keyword outside of functions, whereas 1.25.0 (which was introduced in 06fa1c46fc32) do not allow this anymore (leading to the following error when executing the script: "file: local: line nn: not in a function"). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> 
Older busybox versions allowed using the local keyword outside of
functions, whereas 1.25.0 (which was introduced in 06fa1c46fc32) do not
allow this anymore (leading to the following error when executing the
script: "file: local: line nn: not in a function").

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
ramips: add support for Dovado tiny AC 2015-11-02T10:17:51+00:00 John Crispin john@openwrt.org 2015-11-02T10:17:51+00:00 3760b95702b65de9d6d0f6a1029a654e3b11f72f Add support for Dovado tiny AC wifi router. Soc: mt7620a ram: 64MB flash: 8MB 1x usb 2.0 two gigabit lan ports 5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47348 
Add support for Dovado tiny AC wifi router.

Soc: mt7620a
ram: 64MB
flash: 8MB
1x usb 2.0
two gigabit lan ports

5ghz wlan is not supported on this board since there is no gpl driverfor mt7610e wifi chip.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47348
ramips: add function to change rt2x00 wifi eeprom mac 2015-11-02T10:17:41+00:00 John Crispin john@openwrt.org 2015-11-02T10:17:41+00:00 83693c911a3c4788d44815c6c61cd6f7be6542d5 Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom. Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump. Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com> SVN-Revision: 47347 
Some boards like dovado tiny ac have generic ralink mac in onflash wifi eeprom.
Add eeprom_set_macaddr function to rt2x00 eeprom extract script which changes mac addr insde eeprom dump.

Signed-off-by: Andrej Vlasic <andrej.vlasic0@gmail.com>

SVN-Revision: 47347
ramips: update BR-6475ND dts 2015-01-08T20:26:02+00:00 John Crispin john@openwrt.org 2015-01-08T20:26:02+00:00 2ea64717e2ef72d7181256daa2528ee147ad99a1 Update firmware location for 2.4GHz radio on the Edimax BR-6475nD. Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org> SVN-Revision: 43881 
Update firmware location for 2.4GHz radio on the Edimax BR-6475nD.

Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org>

SVN-Revision: 43881
ramips: soc wmac eeprom cleanup 2014-07-17T10:55:31+00:00 John Crispin john@openwrt.org 2014-07-17T10:55:31+00:00 f44d3f99803be7ba5c38b26a2d8cbda1c301e893 Move eeprom extraction from scripts to dts files. Additionally there are few other changes like: - whitespace fixes - add partition labels where needed - BR6524N board doesn't exist (lost in translation?) - fix Edimax 3g-6200nl model - add wmac eeprom to dts for Asus RT-N14U board Compile tested all subtargets and their profiles. Run tested on: - Asus RT-N15 - Asus RT-N14U - Buffalo WHR-600D - Argus ATP52B - Sparklan WCR-150GN Few problems noted: - many boards didn't have wmac eeprom information defined at all - several boards don't have any patitions defined (see FIXME comments in dts) Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 41680 
Move eeprom extraction from scripts to dts files.
Additionally there are few other changes like:
- whitespace fixes
- add partition labels where needed
- BR6524N board doesn't exist (lost in translation?)
- fix Edimax 3g-6200nl model
- add wmac eeprom to dts for Asus RT-N14U board

Compile tested all subtargets and their profiles.
Run tested on:
- Asus RT-N15
- Asus RT-N14U
- Buffalo WHR-600D
- Argus ATP52B
- Sparklan WCR-150GN

Few problems noted:
- many boards didn't have wmac eeprom information defined at all
- several boards don't have any patitions defined (see FIXME comments in dts)

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 41680