mtk-20170518/target/linux/ramips/base-files/etc, branch v17.01.2 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: WN3000RPv3: do not setup switch 2017-04-28T15:10:01+00:00 Thibaut VARENE hacks@slashdirt.org 2017-02-12T16:11:08+00:00 8b9f7bd7bd911a8677b6fa8256ab521417f326bf The WN3000RPv3 is a repeater with a single ethernet port. Setting up the switch, even to disable it, is unnecessary and possibly confusing. Configure LAN as eth0 instead. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: add support for Sanlinking D240 2017-04-28T15:09:45+00:00 Kristian Evensen kristian.evensen@gmail.com 2017-02-04T20:28:52+00:00 49ce6d04b0fa56facd37924003df02b4ebf14aab The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> 
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
ramips: ZyXEL Keenetic series update wan mac 2017-04-28T15:07:48+00:00 Vitaly Chekryzhev 13hakta@gmail.com 2017-01-05T11:25:59+00:00 a12655a840b7ba86bf23b389671f386ae58f51a8 Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> 
Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
ramips: correct keenetic-series switch index 2017-04-28T15:07:35+00:00 Vitaly Chekryzhev 13hakta@gmail.com 2017-01-01T21:46:33+00:00 85bca2d0fb6886ebff40c63b73a95d522ae8aba3 Fix switch name typo Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> 
Fix switch name typo

Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
ramips: add support for Netgear WN3000RPv3 2017-04-28T15:07:24+00:00 Thibaut VARENE hacks@slashdirt.org 2017-01-18T10:34:56+00:00 1aee42c6a9d297e5a8bd241318338217b86c3070 This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
This patch adds support for the Netgear WN3000RPv3
http://www.netgear.com/support/product/wn3000rpv3.aspx

Specifications:
- SoC: MediaTek MT7620A (580MHz, ramips)
- RAM: 32MB DDR
- Storage: 8MB NOR SPI flash
- Wireless: builtin MT7620A, 2x2:2 with u.FL connectors
- Ethernet: 1x100M
- Serial: JP1 header, 57600-8N1
- Stock firmware based on OpenWRT Kamikaze

Like the EX2700, the bootloader expects a secondary image signature,
see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577
This is why the same fakeroot image is used for the WN3000

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: fix mac address of miwifi-mini 2017-04-28T15:07:04+00:00 BangLang Huang banglang.huang@foxmail.com 2017-01-18T09:45:48+00:00 846457fdbffaffdf44d668715e88cb21765ec6c9 For the miwifi-mini, the offset of ethernet mac should be 0x28 which you can easyily dump from 'Factory' partition. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com> 
For the miwifi-mini, the offset of ethernet mac should be 0x28
which you can easyily dump from 'Factory' partition.

Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
ramips: WN3000RPv3: do not setup switch 2017-04-28T15:02:48+00:00 Thibaut VARENE hacks@slashdirt.org 2017-02-12T16:11:08+00:00 dbd2212205908eac3afce45f3c05e805143728cf The WN3000RPv3 is a repeater with a single ethernet port. Setting up the switch, even to disable it, is unnecessary and possibly confusing. Configure LAN as eth0 instead. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
The WN3000RPv3 is a repeater with a single ethernet port. Setting up the
switch, even to disable it, is unnecessary and possibly confusing.

Configure LAN as eth0 instead.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: fix Linksys RE6500 switch port mapping 2017-03-07T16:39:34+00:00 Jo-Philipp Wich jo@mein.io 2017-03-07T16:38:30+00:00 f8e08ffd94ded1b3b3ae58566d130c2dfa71e531 Properly map the internal switch ports to the proper LAN1..LAN4 labels. Fixes #530. Signed-off-by: Jo-Philipp Wich <jo@mein.io> 
Properly map the internal switch ports to the proper LAN1..LAN4 labels.

Fixes #530.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ramips: Correct switch configuration for Newifi D1 2017-02-13T09:25:19+00:00 Chuanhong Guo gch981213@gmail.com 2017-02-11T13:32:07+00:00 57dfbac6ff6934ce41cb40cda93caf93ad10053a Signed-off-by: Chuanhong Guo <gch981213@gmail.com> 
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ramips: Added Onion Omega2 and Omega2+ 2017-01-15T16:43:14+00:00 Lazar Demin lazar@onion.io 2017-01-09T19:59:56+00:00 ab90f15c89da6aeadf8b95554fcd8ab8e3f433d0 This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io> 
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>