mtk-20170518/target/linux/ramips/base-files, branch master MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: add support for TP-Link TL-MR3020 v3 2018-09-06T19:36:42+00:00 Carlo Nel carlojnel@gmail.com 2018-08-26T19:11:59+00:00 6bbb2202551be394fead2efd99eb946f846fc63d TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N. This PR is based on the work of @meyergru[1], with his permission. Specification: - MediaTek MT7628N/N (575 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz - 1x 10/100 Mbps Ethernet Flash instruction: The only way to flash the image in TL-MR3020 v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with the LAN port, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. [1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3 Signed-off-by: Carlo Nel <carlojnel@gmail.com> 
TP-Link TL-MR3020 v3 is a pocket-size router based on MediaTek MT7628N.

This PR is based on the work of @meyergru[1], with his permission.

Specification:
- MediaTek MT7628N/N (575 Mhz)
- 64 MB of RAM
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 1x 10/100 Mbps Ethernet

Flash instruction:

The only way to flash the image in TL-MR3020 v3 is to use
tftp recovery mode in U-Boot:

1. Configure PC with static IP 192.168.0.225/24 and tftp server.
2. Rename "openwrt-ramips-mt76x8-tplink_tl-mr3020-v3-squashfs-tftp-recovery.bin"
   to "tp_recovery.bin" and place it in tftp server directory.
3. Connect PC with the LAN port, press the reset button, power up
   the router and keep button pressed for around 6-7 seconds, until
   device starts downloading the file.
4. Router will download file from server, write it to flash and reboot.

[1] https://github.com/meyergru/lede-source/commits/TL-MR3020-V3

Signed-off-by: Carlo Nel <carlojnel@gmail.com>
ramips: drop pointless default led definitions 2018-08-29T07:39:32+00:00 Mathias Kresin dev@kresin.me 2018-08-18T10:07:08+00:00 c134210b8f7e18b43641b6c2176e7a3e6baed030 The LEDs should be triggered/lit by any kind of state change instead of turned on/off unconditional. If LEDs really need to be turned off by default, it should be done via the default-state devicetree led property. The handling of the wndr3700v5 and wt3020 power led is at least strange. Something is for sure wrong with them. Either the leds are misnamed, the default off trigger is a typo or the polarity of the gpios is wrong. Drop the power led from userspace and wait for someone with access to the hardware to fix it properly. Signed-off-by: Mathias Kresin <dev@kresin.me> 
The LEDs should be triggered/lit by any kind of state change instead of
turned on/off unconditional.

If LEDs really need to be turned off by default, it should be done via
the default-state devicetree led property.

The handling of the wndr3700v5 and wt3020 power led is at least
strange. Something is for sure wrong with them. Either the leds are
misnamed, the default off trigger is a typo or the polarity of the
gpios is wrong. Drop the power led from userspace and wait for someone
with access to the hardware to fix it properly.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: express diag led handling via devicetree 2018-08-29T07:34:07+00:00 Mathias Kresin dev@kresin.me 2018-08-18T09:38:13+00:00 99045dfc5989e732f671de5d145532f0fe8c0ce1 Use the default-state property to express the desired led handling in the devicetree source file instead of the userspace. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the default-state property to express the desired led handling in
the devicetree source file instead of the userspace.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: remove default on userspace trigger for diag leds 2018-08-29T07:26:24+00:00 Mathias Kresin dev@kresin.me 2018-08-18T09:09:29+00:00 111907e8d319eb05e7a5ef7a0cc6ec55cb069242 All the LEDs are turned on by diag.sh at the end of the boot process. No need to do the same via userspace configuration again. Signed-off-by: Mathias Kresin <dev@kresin.me> 
All the LEDs are turned on by diag.sh at the end of the boot process.
No need to do the same via userspace configuration again.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix multi colour led handling 2018-08-29T07:24:49+00:00 Mathias Kresin dev@kresin.me 2018-08-18T10:22:25+00:00 56e6ebdea42aab76d6ef54e0296c6bf946956684 All boards either have a multi colour led or a single lightpipe. It makes it impossible to handle the LEDs individual. Change the LED config for these boards to take it into account. Signed-off-by: Mathias Kresin <dev@kresin.me> 
All boards either have a multi colour led or a single lightpipe. It
makes it impossible to handle the LEDs individual. Change the LED
config for these boards to take it into account.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: rt-n12p: use the boardname helper variable 2018-08-29T07:23:11+00:00 Mathias Kresin dev@kresin.me 2018-08-29T06:59:46+00:00 fe1e90deb4cacbac4841507b9bf2a85eb275a823 Use the helper variable for the Asus RT-N12P as it is done by all boards. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the helper variable for the Asus RT-N12P as it is done by all
boards.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: mt7620: add dir-810l network config 2018-08-23T20:42:15+00:00 Roger Pueyo Centelles roger.pueyo@guifi.net 2018-08-23T13:04:31+00:00 524c17d8654a3137a1de8e59cf4a9881575b7285 The device was not included in the /etc/board.d/02_network file, so the network wouldn't be properly set up on boot. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> 
The device was not included in the /etc/board.d/02_network file, so
the network wouldn't be properly set up on boot.

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
ramips: add support for ELECOM WRC-1900GST 2018-08-23T20:42:09+00:00 NOGUCHI Hiroshi drvlabo@gmail.com 2018-08-18T23:05:15+00:00 ad10e71becfb36d36c81c5b0e898c4ea7912d778 ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A. This is almost same as WRC-2533GST except wireless specs. Specifications: - SoC : MT7621A (four logical CPU cores) - RAM : 128MiB - ROM : 16MiB of SPI NOR-FLASH - wireless : 5GHz : 3T3R up to 1300Mbps/11ac with MT7615 2.4GHz : 3T3R up to 600Mbps/11n with MT7615 - Ethernet : 5 ports, all ports is capable of 1000base-T - Ether switch : MT7530 (MT7621A built-in) - LEDs : 4 LEDs - buttons : 2 buttons and 1 slide-switch - UART : header is on PCB, 57600bps Flash instruction using factory image: 1. Connect the computer to the LAN port of WRC-1900GST 2. Connect power cable to WRC-1900GST and turn on it 3. Access to "https://192.168.2.1/" and open firmware update page ("ファームウェア更新") 4. Select the OpenWrt factory image and click apply ("適用") button 5. Wait ~150 seconds to complete flashing Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> 
ELECOM WRC-1900GST is a wireless router, based on Mediatek MT7621A.
This is almost same as WRC-2533GST except wireless specs.

Specifications:

  - SoC : MT7621A (four logical CPU cores)
  - RAM : 128MiB
  - ROM : 16MiB of SPI NOR-FLASH
  - wireless :
          5GHz : 3T3R up to 1300Mbps/11ac with MT7615
          2.4GHz : 3T3R up to 600Mbps/11n with MT7615
  - Ethernet : 5 ports, all ports is capable of 1000base-T
  - Ether switch : MT7530 (MT7621A built-in)
  - LEDs : 4 LEDs
  - buttons : 2 buttons and 1 slide-switch
  - UART : header is on PCB, 57600bps

Flash instruction using factory image:

 1. Connect the computer to the LAN port of WRC-1900GST
 2. Connect power cable to WRC-1900GST and turn on it
 3. Access to "https://192.168.2.1/" and open firmware update
    page ("ファームウェア更新")
 4. Select the OpenWrt factory image and click apply ("適用")
    button
 5. Wait ~150 seconds to complete flashing

Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
treewide: consolidate upgrade state set 2018-08-16T19:20:57+00:00 Mathias Kresin dev@kresin.me 2018-08-15T16:55:01+00:00 56b8ac1e86eb5b0c500cbf8db60ce00aff01bcec Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Set the (sys)upgrade state when sourcing the stage2 script instead of
setting the state for each target individual.

This change fixes the, due to a missing state set, not working upgrade
led on ath79 and apm821xx.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: add support for D-Link DWR-118-A2 2018-08-15T05:42:36+00:00 Cezary Jackiewicz cezary@eko.one.pl 2018-04-19T17:34:22+00:00 37af596593b0e84d0a076ab8f173066e3d7bc810 The DWR-118-A2 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 128 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7612EN) - 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN) - 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN) - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - GELAN not working - flash is very slow The status led has been assigned to the dwr-118-a2:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> 
The DWR-118-A2 Wireless Router is based on the MT7620A SoC.

Specification:

- MediaTek MT7620A (580 Mhz)
- 128 MB of RAM
- 16 MB of FLASH
- 1x 802.11bgn radio
- 1x 802.11ac radio (MT7612EN)
- 4x 10/100 Mbps Ethernet (1 WAN and 3 LAN)
- 1x 10/100/1000 Mbps Marvell Ethernet PHY (1 LAN)
- 2x external, non-detachable antennas
- 1x USB 2.0
- UART (J1) header on PCB (57600 8n1)
- 7x LED (5x GPIO-controlled), 2x button
- JBOOT bootloader

Known issues:
- GELAN not working
- flash is very slow

The status led has been assigned to the dwr-118-a2:green:internet led.
At the end of the boot it is switched off and is available for other
operation. Work correctly also during sysupgrade operation.

Installation:
Apply factory image via http web-gui or JBOOT recovery page

How to revert to OEM firmware:
- push the reset button and turn on the power. Wait until LED start
  blinking (~10sec.)
- upload original factory image via JBOOT http (IP: 192.168.123.254)

Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>