mtk-20170518/target/linux/ramips/base-files, branch v17.01.1 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: fix Linksys RE6500 switch port mapping 2017-03-07T16:39:34+00:00 Jo-Philipp Wich jo@mein.io 2017-03-07T16:38:30+00:00 f8e08ffd94ded1b3b3ae58566d130c2dfa71e531 Properly map the internal switch ports to the proper LAN1..LAN4 labels. Fixes #530. Signed-off-by: Jo-Philipp Wich <jo@mein.io> 
Properly map the internal switch ports to the proper LAN1..LAN4 labels.

Fixes #530.

Signed-off-by: Jo-Philipp Wich <jo@mein.io>
ramips: Correct switch configuration for Newifi D1 2017-02-13T09:25:19+00:00 Chuanhong Guo gch981213@gmail.com 2017-02-11T13:32:07+00:00 57dfbac6ff6934ce41cb40cda93caf93ad10053a Signed-off-by: Chuanhong Guo <gch981213@gmail.com> 
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
ramips: Added Onion Omega2 and Omega2+ 2017-01-15T16:43:14+00:00 Lazar Demin lazar@onion.io 2017-01-09T19:59:56+00:00 ab90f15c89da6aeadf8b95554fcd8ab8e3f433d0 This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io> 
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
ramips: add support for VoCore2 2017-01-13T07:32:35+00:00 Andrew Yong me@ndoo.sg 2017-01-08T06:30:10+00:00 3f31029b190417e12f4d19d9999cd52ec76d0f85 This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg> 
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
ramips: MiWiFi Nano fixes 2017-01-02T18:16:54+00:00 L. D. Pinney ldpinney@gmail.com 2016-12-29T07:43:08+00:00 b28e94d4bfa1f81219765fc395e63ca81badd8df Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use new image build code for more devices 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-11-21T07:46:48+00:00 0cf581ca3a2a692938003a7038d93f2e24d9125a Signed-off-by: Mathias Kresin <dev@kresin.me> 
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use different board names for variants 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-12-23T08:46:48+00:00 a75ce960ac1b9d67af280e17e1e653b3b39def20 Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use D-Link DIR-600 B1 image for B2 version 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-11-25T12:25:29+00:00 d2b1148e755254e2e41417fd18de03882e13bba8 Everything set for the B1 is identical to the values uses for the B2 version. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Everything set for the B1 is identical to the values uses for the B2
version.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix image validation errors 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-12-01T06:37:03+00:00 d2b6bf141662429d542b23e9e8f44245a77710a5 The name from the Device define will be used in the metadata. Due to typos/different spelling, this name might not match the one exported in /lib/ramips.sh. Fix all name mismatches which were found by checking if the name used in the metadata exists in /lib/ramips.sh. Signed-off-by: Mathias Kresin <dev@kresin.me> 
The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use destinct 11AC NAS board name 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-12-23T07:21:31+00:00 ae3ac76e565724e188138dafe38ebeed122e2cf8 Use a distinct board name even if the board is near to identical to the WeVO W2914NS v2. To make sure that a 11AC NAS image can not be installed on a WeVO W2914NS v2, both board need to use different names. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use a distinct board name even if the board is near to identical to
the WeVO W2914NS v2.

To make sure that a 11AC NAS image can not be installed on a
WeVO W2914NS v2, both board need to use different names.

Signed-off-by: Mathias Kresin <dev@kresin.me>