mtk-20170518/target/linux/ramips/dts, branch v17.01.1 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: add RP-N53 pcie wireless eeprom 2017-04-12T08:13:40+00:00 Mathias Kresin dev@kresin.me 2017-04-09T07:14:52+00:00 f2f672c32ca32643c6985ff4f7f994934725cd40 Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata. Disable the 2.4GHz band as this band has no antennas attached but is enabled in the eeprom/caldata. Fixes: FS#691 Signed-off-by: Mathias Kresin <dev@kresin.me> 
Fix the PCIe 5GHz wireless by using the on flash eeprom/caldata.
Disable the 2.4GHz band as this band has no antennas attached but is
enabled in the eeprom/caldata.

Fixes: FS#691

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix WHR-600D eeprom dt property 2017-04-12T08:13:37+00:00 Mathias Kresin dev@kresin.me 2017-04-09T07:12:55+00:00 f3dc2ffdd4462dd08220fbafc4ac2971f7ef43b0 Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as this board have a RT5592 and uses the rt2x00 driver. The mediathek device tree bindings do not work here. Fixes: FS#691 Fixes: d8dd207ea6f2 ("ramips: use the ralink,mtd-eeprom device tree property") Signed-off-by: Mathias Kresin <dev@kresin.me> 
Fix the PCIe 5GHz wireless by using the ralink mtd-eeprom property as
this board have a RT5592 and uses the rt2x00 driver. The mediathek
device tree bindings do not work here.

Fixes: FS#691

Fixes: d8dd207ea6f2 ("ramips: use the ralink,mtd-eeprom device tree property")
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix PWM pin mux conflict in dtsi 2017-02-16T08:54:17+00:00 Furong Xu xfr@outlook.com 2017-02-16T02:00:48+00:00 71ea3b481406cd44d2d94da60e6fdec5bc8a9eb9 GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict [ 0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm [ 0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22 [ 0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0 on device rt2880-pinmux [ 0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back Keep PWM disabled. Signed-off-by: Furong Xu <xfr@outlook.com> 
GPIO18 and GPIO19 on OMEGA2(+) should be GPIO mode, enable PWM lead to a conflict

[    0.290633] rt2880-pinmux pinctrl: pin io18 already requested by pinctrl; cannot claim for 10005000.pwm
[    0.299722] rt2880-pinmux pinctrl: pin-18 (10005000.pwm) status -22
[    0.305729] rt2880-pinmux pinctrl: could not request pin 18 (io18) from group pwm0  on device rt2880-pinmux
[    0.315131] mtk-pwm 10005000.pwm: Error applying setting, reverse things back

Keep PWM disabled.

Signed-off-by: Furong Xu <xfr@outlook.com>
ramips: add missing DTS pcie node for WSR-600 2017-01-31T09:29:29+00:00 Felix Fietkau nbd@nbd.name 2017-01-31T09:27:25+00:00 bda982b97fae6073ab65c05c1c47bb5f71f8dccf Enables PCI bus and support for the MT7603 and RT5592 chips Signed-off-by: Felix Fietkau <nbd@nbd.name> 
Enables PCI bus and support for the MT7603 and RT5592 chips

Signed-off-by: Felix Fietkau <nbd@nbd.name>
ramips: Added Onion Omega2 and Omega2+ 2017-01-15T16:43:14+00:00 Lazar Demin lazar@onion.io 2017-01-09T19:59:56+00:00 ab90f15c89da6aeadf8b95554fcd8ab8e3f433d0 This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io) Specifications: - SoC: MediaTek MT7688AN (580MHz, ramips) - Omega2 - RAM: 64MB DDR - Storage: 16MB NOR SPI flash onboard - Omega2+ - RAM: 128MB DDR - Storage: 32MB NOR SPI flash onboard + microSD slot - Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter - Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port - Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock) - All Docks Provide: - Micro-USB port to provide power to the Omega - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial - USB 2.0 socket connected to Omega - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide: - Omega GPIO breakout - Allows for connection of Omega Expansions: - Ethernet Expansion - Relay Expansion - PWM Expansion - OLED Expansion - Ethernet Expansion - Proto Expansion - Cellular Expansion Signed-off-by: Lazar Demin <lazar@onion.io> 
This patch adds support for the Onion Omega2 and Omega2+ (https://onion.io)

Specifications:
- SoC: MediaTek MT7688AN (580MHz, ramips)
- Omega2
  - RAM: 64MB DDR
  - Storage: 16MB NOR SPI flash onboard
- Omega2+
  - RAM: 128MB DDR
  - Storage: 32MB NOR SPI flash onboard + microSD slot
- Wireless: Built into MT7688AN (mt76) with onboard 1x chip antenna and u.FL connecter
- Ethernet: 1x100M pins on Omega2 & Omega2+, can use Ethernet Expansion and an Omega Dock to get a physical Ethernet port
- Strongly recommend using the Omega2 & Omega2+ with a Dock (Expansion Dock, Power Dock, Arduino Dock 2, Mini Dock)
  - All Docks Provide:
    - Micro-USB port to provide power to the Omega
      - On the Expansion and Mini Docks, can also access the terminal (UART0) via serial
    - USB 2.0 socket connected to Omega
  - Just the Expansion Dock, Power Dock, and Arduino Dock 2 provide:
    - Omega GPIO breakout
    - Allows for connection of Omega Expansions:
      - Ethernet Expansion
      - Relay Expansion
      - PWM Expansion
      - OLED Expansion
      - Ethernet Expansion
      - Proto Expansion
      - Cellular Expansion

Signed-off-by: Lazar Demin <lazar@onion.io>
ramips: fix WLI-TX4-AG300N boot and network 2017-01-13T07:32:35+00:00 Yo Abe abe.geel@gmail.com 2017-01-11T18:07:14+00:00 29097b95ba266743f74401cbb905186bb74a414a Partition label "linux" prevents the root file system to be mounted at boot time leading to a kernel panic. After changing it to "firmware", the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data" are correctly recognized. The attached IP175C 10/100 MBit switch cannot connect to a link with fixed 1000Mbit speed. The correct link speed is 100MBit. The switch is detected and can be configured via mdio bus and should allow two separable VLANs to be configured for the 4 available ports. Signed-off-by: Yo Abe <abe.geel@gmail.com> [picked from openwrt/PR#330] Signed-off-by: Mathias Kresin <dev@kresin.me> 
Partition label "linux" prevents the root file system to be mounted at
boot time leading to a kernel panic. After changing it to "firmware",
the 2 uimage partitions "kernel", "rootfs" and squashfs "rootfs_data"
are correctly recognized.

The attached IP175C 10/100 MBit switch cannot connect to a link with
fixed 1000Mbit speed. The correct link speed is 100MBit. The switch
is detected and can be configured via mdio bus and should allow two
separable VLANs to be configured for the 4 available ports.

Signed-off-by: Yo Abe <abe.geel@gmail.com>
[picked from openwrt/PR#330]
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: add support for VoCore2 2017-01-13T07:32:35+00:00 Andrew Yong me@ndoo.sg 2017-01-08T06:30:10+00:00 3f31029b190417e12f4d19d9999cd52ec76d0f85 This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg> 
This patch adds support for the VoCore VoCore2 and its complementary
"ultimate" dock.

Specifications:
- SoC: MediaTek MT7628AN (580MHz, ramips)
- RAM: 128MB DDR2 166MHz
- Storage: 16MB NOR SPI flash onboard + microSD slot on dock
- Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2
            boards with onboard 1x chip antenna
- Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header
- Dock hardware:
  - USB 2.0 socket
  - MicroSD socket
  - 100Mbps Ethernet x1
  - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S
    DAC/ADC (support WIP)
  - Micro USB for power and console (UART2)

Initial installation:
- VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on
  SSID "VoCore2"
- Connect to VoCore2 by Ethernet or Wi-Fi
- `ssh root@192.168.1.1` (password is "vocore")
- scp/wget/etc. LEDE sysupgrade.bin to VoCore2
- `sysupgrade -n <your image>.bin` (don't keep old config, as the
  original firmware uses Ralink SDK Wi-Fi drivers and not
  mt76+mac80211)
- after sysupgrade completes, Wi-Fi will be disabled by default so use
  Ethernet or the micro USB console to configure Wi-Fi again

Signed-off-by: Andrew Yong <me@ndoo.sg>
ramips: MiWiFi Nano fixes 2017-01-02T18:16:54+00:00 L. D. Pinney ldpinney@gmail.com 2016-12-29T07:43:08+00:00 b28e94d4bfa1f81219765fc395e63ca81badd8df Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use the the dt-bindings macros and add the reset button.

Set the correct polarity for the LEDs and drop the default state.
Remove all trigger for the LEDs. According to the manual the LEDs are
only used to show the operation state, where blue means normal
operation.

Use the MAC-Addresses stored in EEPROM for the ethernet and the
wireless interface.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
[use leds only for boot status indication, add proper commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use new image build code for more devices 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-11-21T07:46:48+00:00 0cf581ca3a2a692938003a7038d93f2e24d9125a Signed-off-by: Mathias Kresin <dev@kresin.me> 
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: use different board names for variants 2016-12-24T09:03:38+00:00 Mathias Kresin dev@kresin.me 2016-12-23T08:46:48+00:00 a75ce960ac1b9d67af280e17e1e653b3b39def20 Use different names for flash size related board variants, to make sure that only images for the actual flash size are considered as valid by the image validation code. Remove the flash size suffix from the string returned by ramips_board_detect() to ensure that existing scripts relying on the former used boardname are still working. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Use different names for flash size related board variants, to make sure
that only images for the actual flash size are considered as valid by
the image validation code.

Remove the flash size suffix from the string returned by
ramips_board_detect() to ensure that existing scripts relying on the
former used boardname are still working.

Signed-off-by: Mathias Kresin <dev@kresin.me>