mtk-20170518/target/linux/ramips/dts, branch v17.01.3 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: fix WHR-1166D WAN port 2017-08-11T16:13:38+00:00 Mathias Kresin dev@kresin.me 2017-08-09T18:17:43+00:00 ff414fb575a43ada264186fe74e57fb605f20b7f By adding the ICPlus IP1001 phy driver an already set RGMII delay mode is reset during driver load. Set the rgmii rx delay to fix corrupt/no packages in case the WAN port negotiates to 1000MBit. Fixes: FS#670 Signed-off-by: Mathias Kresin <dev@kresin.me> 
By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.

Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.

Fixes: FS#670

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: ArcherC50v1: fix wlan2g MAC address 2017-08-06T07:31:05+00:00 Thibaut VARENE hacks@slashdirt.org 2017-08-04T15:22:03+00:00 982612dba26f042f8b9a524996b0774d3c8e747a By default the wlan eprom contains the generic ralink MAC which is not the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses are decremented from the ethernet MAC. This patch fixes the MAC address for wlan2g in line with OFW. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.

This patch fixes the MAC address for wlan2g in line with OFW.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: add missing partitions 2017-08-02T19:16:20+00:00 Mathias Kresin dev@kresin.me 2017-07-31T16:00:35+00:00 57a8f36ac486f310fc9bdc7d394f36c11e083511 The partitions were lost during migration to device tree. Signed-off-by: Mathias Kresin <dev@kresin.me> 
The partitions were lost during migration to device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: Archer C50v1: fix power led 2017-07-29T10:07:16+00:00 Thibaut VARENE hacks@slashdirt.org 2017-07-29T09:32:44+00:00 c407e6c2f29b96fe589370125595004e856f78d5 01_leds had a workaround for the power led to compensate for the inverted GPIO state. This patch was missing from my previous commit. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> [add the power led default-state which was omitted in the last commit by me] Signed-off-by: Mathias Kresin <dev@kresin.me> 
01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: Archer C50v1: fix LEDs active levels 2017-07-29T07:24:59+00:00 Thibaut VARENE hacks@slashdirt.org 2017-07-28T21:26:40+00:00 a9439344e71287cb172cf73880f800dc374fc5b7 All LEDs GPIOs are active low on this device. WAN and POWER states were inverted. Add default state for power. Tested on Archer C50v1. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
All LEDs GPIOs are active low on this device.

WAN and POWER states were inverted. Add default state for power.

Tested on Archer C50v1.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: fix wps button gpio for DWR-512 2017-07-25T19:02:27+00:00 Giuseppe Lippolis giu.lippolis@gmail.com 2017-07-18T20:55:53+00:00 e08b8255ec41946ed80f77dd551e93af9de01cb9 The WPS button is at GPIO#7. Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com> 
The WPS button is at GPIO#7.

Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
ramips: DTS: VoCore2 improvements/fixes 2017-07-25T19:02:27+00:00 Paul Wassi p.wassi@gmx.at 2017-07-22T09:15:55+00:00 ece85e2e49e021cea0455e19182c67854bbb9eb8 The VoCore2 features 128MB of RAM, therefore set memory in DTS to 128*1024*1024 = 0x8000000 The board's LED is connected to GND, set it to ACTIVE_HIGH here. Make serial console working again on kernel 4.9 by change of pinmux configuration. Signed-off-by: Paul Wassi <p.wassi@gmx.at> 
The VoCore2 features 128MB of RAM, therefore set
memory in DTS to 128*1024*1024 = 0x8000000
The board's LED is connected to GND, set it to
ACTIVE_HIGH here.
Make serial console working again on kernel 4.9 by
change of pinmux configuration.

Signed-off-by: Paul Wassi <p.wassi@gmx.at>
ramips: fix Xiaomi MiWiFi Nano firmware partition size 2017-07-08T06:53:52+00:00 Mathias Kresin dev@kresin.me 2017-03-23T19:30:25+00:00 3214e174a07f5b333ae6f3fe5a857c8324e9ae27 Even the commit message of the patch adding support for the MiWiFi Nano says that a 16 MB flash chip is used. Extend the firmware partition to make use of all available flash space. Fixes: FS#622 Signed-off-by: Mathias Kresin <dev@kresin.me> 
Even the commit message of the patch adding support for the MiWiFi Nano
says that a 16 MB flash chip is used. Extend the firmware partition to
make use of all available flash space.

Fixes: FS#622

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix Phicomm K1S(PSG1208) pinmux 2017-06-12T19:10:14+00:00 小桥 29551030@qq.com 2017-03-05T07:53:40+00:00 2e206c79ccbc1bd4289654673b4db64a26380fb6 Use gpio function for pins with LEDs. Signed-off-by: 小桥 <29551030@qq.com> 
Use gpio function for pins with LEDs.

Signed-off-by: 小桥 <29551030@qq.com>
ramips: add support for Sanlinking D240 2017-04-28T15:09:45+00:00 Kristian Evensen kristian.evensen@gmail.com 2017-02-04T20:28:52+00:00 49ce6d04b0fa56facd37924003df02b4ebf14aab The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> 
The Sanlinking Technologies D240
(http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same
device as the ZBT WE826, so adding support for it in LEDE is straight forward.
The differences is that the D240 has two mini-PCIe slots (instead of one), blue
LEDs and supports PoE.

Specification:
* CPU: MT7620A
* 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps.
* 16 MB Flash.
* 128 MB RAM.
* 1x USB 2.0 port.
* 2x mini-PCIe slots.
* 2x SIM slots.
* 1x 2.4Ghz WIFI.
* 1x button.

Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to
test the SD card reader.

The device comes pre-installed with an older version of OpenWRT, including Luci.
In order to install LEDE, you need to follow the existing procedure for updating
OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware
using the sysupgrade-image. Remember to select that you do not want to keep
existing settings. The default router address is 192.168.10.1 and
username/password admin/root (at least on my devices).

If you brick the device, the procedure for recovery is the same as for the
WE826. Please see the wiki page for that device for instructions.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>