According to the datasheet the REFCLK pin is shared with GPIO#37 and
the PERST pin is shared with GPIO#36.

While at it fix a typo inside the pinmux setup code. The function is called
refclk and not reclk.

Update device tree source files accordingly.

Signed-off-by: Mathias Kresin <dev@kresin.me>

This commit adds missing the GPIO key used as reset button.
Nexx WT1520 has a GPIO key for factory reset, but it's not defined in
WT1520.dtsi and cannot use it.

Drop the UART (full) from the device tree source file, it was never
used for this board. Adjust the kernel bootargs accordingly.

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[add note about dropped UART (full) to the commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>

Setting the pins of the uartf group to gpio+i2s at the time the i2c
driver loads is to late for the WPS gpio button.

The gpio-keys driver fails to load since the pin used by the WPS button
is not yet set to GPIO. The WPS button with the rfkill keycode is
essential for this wifi only board.

Add the missing sound and i2c kernel modules corresponding to the
device nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>

Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.

Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.

Add the missing kernel packages for USB and microSD card reader to the
default package selection.

Fix the maximum image size value. The board has a 32MByte flash chip.

Fixes: FS#1055

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>

Backport required DT changes from commit dabdd123c90c.
Significantly improves stability and performance for MT76x2 and MT7603

Signed-off-by: Felix Fietkau <nbd@nbd.name>

By adding the ICPlus IP1001 phy driver an already set RGMII delay mode
is reset during driver load.

Set the rgmii rx delay to fix corrupt/no packages in case the WAN port
negotiates to 1000MBit.

Fixes: FS#670

Signed-off-by: Mathias Kresin <dev@kresin.me>

By default the wlan eprom contains the generic ralink MAC which is not
the vendor (TP-Link) one. Based on OFW bootlog, it appears that addresses
are decremented from the ethernet MAC.

This patch fixes the MAC address for wlan2g in line with OFW.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>

The partitions were lost during migration to device tree.

Signed-off-by: Mathias Kresin <dev@kresin.me>

01_leds had a workaround for the power led to compensate for the
inverted GPIO state. This patch was missing from my previous commit.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
[add the power led default-state which was omitted in the last commit
by me]
Signed-off-by: Mathias Kresin <dev@kresin.me>

All LEDs GPIOs are active low on this device.

WAN and POWER states were inverted. Add default state for power.

Tested on Archer C50v1.

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>