mtk-20170518/target/linux/ramips/files/drivers/net, branch mtk-20170518

move files to files-3.7

2013-04-03T09:58:44+00:00

Signed-off-by: John Crispin 

SVN-Revision: 36161

fix for non-blinking LAN LEDs

2013-01-28T18:06:31+00:00

https://dev.openwrt.org/ticket/12830

SVN-Revision: 35359

ramips: ramips_eth: use Kconfig definition to enable debug

2012-11-25T14:25:54+00:00

The Kconfig identifier to enable debugging in the driver was different from the
actually used one. Fix that.

Signed-off-by: Paul Fertser 
Signed-off-by: Gabor Juhos 

SVN-Revision: 34332

move ethernet hw init to init/uninit functions

2012-11-12T21:35:01+00:00

This should fix the stalled irq problem seen by several people.
This is not the real fix, but rather moves the bug to the un/init patch of the driver.
The real bug still needs to be fixed, but this workaround should be suffcient to make
the ethernet stable.

SVN-Revision: 34177

add ethernet support for rt5350

2012-09-25T14:47:08+00:00

SVN-Revision: 33548

make ramips ethernet use a register mapping table

2012-09-25T14:46:58+00:00

SVN-Revision: 33547

ramips: Add missing andmask to ramips_esw register read for recv_good value.

2012-09-05T20:08:43+00:00

Add missing andmask to ramips_esw register read for recv_good value.

Without the mask, recv_bad leaks into the recv_good packet count.
Didn't notice the bug before since you don't usually get bad
packets, so I only saw it when I was playing with overlength packets
earlier...

Signed-off-by: Tobias Diedrich 

SVN-Revision: 33322

ramips: Use doubletagging to disable ramips_esw vlan by default, it seems more reliable.

2012-09-05T20:08:42+00:00

Use doubletagging to disable ramips_esw vlan by default, it seems
more reliable.

Daniel Golle found an issue where sometimes (possibly only for
RT3352) the default vlan disable method (clearing en_vlan, untag,
doubletag and putting all ports into vlan 0) doesn't work and the
packets get sent out vlan-tagged with vlan 0.

Instead switch to using the doubletagging method (allow doubletagged
packets, put all ports into vlan 0 with untag enabled) by default.

Unless someone figures out a way to really globally disable vlan for
this switch, this seems like the best (most reliable) option.

I did some tests regarding maximum packet size and did not see any

difference between the two methods, both allow for slightly bigger packets
than the ramips_main.c ethernet driver (ping stops going through
above "ping -s 1472" (1514 bytes), on the switch packets are recv_good until
"ping -s 1490", or about 1532 bytes).

Signed-off-by: Tobias Diedrich 

SVN-Revision: 33321

ramips: Power down phy on disabled switch ports

2012-08-29T10:37:45+00:00

Power down phy on disabled switch ports.

Haven't measured this myself yet, but according to this
http://www.8devices.com/community/viewtopic.php?f=6&t=156
it can save about 300mW of power.

[juhosg: fix checkpatch warning]

Signed-off-by: Tobias Diedrich 

SVN-Revision: 33304

ramips: Rename POC registers

2012-08-29T10:37:41+00:00

Rename POC registers.

The current code uses POC1-POC3.

The datasheet uses:
POC1: Port Control 0
POC1: Port Control 1
POC2: Port Control 2

So the first POC1 is a typo that should have been POC0, rename the
registers to POC0-POC2 accordingly.

Signed-off-by: Tobias Diedrich 

SVN-Revision: 33302