mtk-20170518/target/linux/ramips/image/rt288x.mk, branch v17.01.3

ramips: add ip17xx support to WLI-TX4-AG300N

2017-04-28T15:08:50+00:00

ramips/rt288x WLI-TX4-AG300N was missing support for its 100Mbit switch which
should be included by default.

Signed-off-by: Yo Abe 
[Jo-Philipp Wich: picked from OpenWrt PR#359, rewrap commit msg, fix Sob]
Signed-off-by: Jo-Philipp Wich

ramips: fix Airlink AR725W device title

2017-03-01T19:37:36+00:00

Gemtek is the ODM but the board was sold by Airlink101.

Signed-off-by: Mathias Kresin

ramips: fix AR670W partition alignment

2017-02-08T05:16:53+00:00

mtdsplit_lzma requires that the rootfs be aligned to a block boundary.
Pad the kernel partition to make this so.

Signed-off-by: Claudio Leite

ramips: fix Airlink AR725W factory image build

2017-02-04T11:54:40+00:00

The factory image can't be bigger than 3328 KByte. If the image is
bigger than that, the gemtek-header tool throws an error and breaks
the build.

Make sure the output file to which the gemtek header should be added
exists and wasn't removed during the check-size step because of it
size. This will prevent hard errors in case the factory image is to big
similar to what is done for sysupgrade images.

Signed-off-by: Mathias Kresin

ramips: fix image validation errors

2016-12-24T09:03:38+00:00

The name from the Device define will be used in the metadata. Due to
typos/different spelling, this name might not match the one exported in
/lib/ramips.sh.

Fix all name mismatches which were found by checking if the name used
in the metadata exists in /lib/ramips.sh.

Signed-off-by: Mathias Kresin

ramips: add support for PCI based OHCI/EHCI support for F5D8235 V1

2016-12-04T06:03:17+00:00

This router uses an PCI attached NEC EHCI controller to support the single USB port.

Signed-off-by: Tobias Wolf

ramips: add size checks/append metadata where missing

2016-11-27T14:34:23+00:00

Signed-off-by: Mathias Kresin

ramips: fix Airlink AR670W factory image

2016-11-27T14:34:23+00:00

Move the mkwrgimg build step to the makefile. It will be required by
other boards as well.

Signed-off-by: Mathias Kresin

ramips: append metadata to images

2016-11-19T10:24:10+00:00

metadata checks are not enforced yet, because some images are still
being built by legacy code

Signed-off-by: Felix Fietkau

ramips: set blocksize for 4MB devices

2016-09-03T07:56:35+00:00

Set the blocksize for devices having only 4MB of flash for ramips
devices already using the new image build code.

Informations about the used flash chip are gathered from the OpenWrt
wiki, wikidevi, forums, OEM bootlogs or the compatible property in the
device tree source file.

The en25q32b from the AirLive Air3GII does not have 4k support in the
kernel.

For the following boards no information about the used flash chip could
be found and a 64k blocksize is assumed:

  - Ralink V11ST-FE
  - Ralink AP-RT3052-V22RW-2X2
  - MediaTek MT7628 EVB
  - MediaTek MT7621 EVB
  - UPVEL UR-326N4G
  - Buffalo WZR-AGL300NH

Signed-off-by: Mathias Kresin