mtk-20170518/target/linux/ramips/image, branch v17.01.6 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: fix Planex CS-QR10 device packages 2017-11-22T07:19:37+00:00 Mathias Kresin dev@kresin.me 2017-11-18T11:19:00+00:00 7ec639451d0d090e760f097c9ceb4c77c08e605a Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will not be autoselected. Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Add kmod-sound-core, it is a dependency of kmod-sound-mt7620 and will
not be autoselected.

Remove kmod-i2c-core, it will be autoselected by kmod-i2c-ralink.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix DCH-M225 support 2017-11-22T07:19:37+00:00 Mathias Kresin dev@kresin.me 2017-11-18T10:59:22+00:00 6cfa7e57887fe1b021cc50b4b7547d2e51240ac1 Setting the pins of the uartf group to gpio+i2s at the time the i2c driver loads is to late for the WPS gpio button. The gpio-keys driver fails to load since the pin used by the WPS button is not yet set to GPIO. The WPS button with the rfkill keycode is essential for this wifi only board. Add the missing sound and i2c kernel modules corresponding to the device nodes. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Setting the pins of the uartf group to gpio+i2s at the time the i2c
driver loads is to late for the WPS gpio button.

The gpio-keys driver fails to load since the pin used by the WPS button
is not yet set to GPIO. The WPS button with the rfkill keycode is
essential for this wifi only board.

Add the missing sound and i2c kernel modules corresponding to the
device nodes.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix Youku-YK1 support 2017-10-27T09:19:07+00:00 Edmunt Pienkowsky roed@onet.eu 2017-10-21T09:07:43+00:00 3eae19acee79d40ecb151a23f1f79110995f9386 Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me> 
Remove the ephy-pins from the ethernet device tree node. The ephy-pins
are useed to controll the ePHY LEDs and this board doesn't have these.
Instead one of the ePHY pins is used in GPIO mode to control the WAN
LED.

Use the switch LED trigger to control the WAN LED. Move the power LED
handling to diag.sh to show the boot status via this LED.

Add the missing kernel packages for USB and microSD card reader to the
default package selection.

Fix the maximum image size value. The board has a 32MByte flash chip.

Fixes: FS#1055

Signed-off-by: Edmunt Pienkowsky <roed@onet.eu>
[make the commit message more verbose, remove GPIO pinmux for pins not
used as GPIOs]
Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix default usb support for nexx wt3020-8M 2017-10-24T18:36:08+00:00 Alberto Bursi alberto.bursi@outlook.it 2017-10-21T21:53:49+00:00 f5935f78a194525e0b1a261e1cf1c6769e810504 the nexx wt3020-8M has a usb 2.0 port, add usb 2.0 support packages to its default package list. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> 
the nexx wt3020-8M has a usb 2.0 port,
add usb 2.0 support packages to its default package list.

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
ramips: mt7620: do not pad sysupgrade Archer images 2017-10-04T20:22:56+00:00 Thibaut VARENE hacks@slashdirt.org 2017-08-02T14:28:16+00:00 f9a849ca84f596aafd7c167b2410ec5446c84784 The current makefile unnecessarily pads sysupgrade image for Archer devices. This has three implications: 1. higher risk of OOM when uploading the binary image to the device 2. much slower upgrade due to time wasted erasing and writing padding 3. grows image beyond available flash size if metadata are appended This is already fixed in master, albeit in a completely different way (the whole target have been reworked) Fixes: FS#1025, FS#1039 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> 
The current makefile unnecessarily pads sysupgrade image for Archer devices.

This has three implications:
1. higher risk of OOM when uploading the binary image to the device
2. much slower upgrade due to time wasted erasing and writing padding
3. grows image beyond available flash size if metadata are appended

This is already fixed in master, albeit in a completely different way (the
whole target have been reworked)

Fixes: FS#1025, FS#1039

Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
ramips: fix Omnima MiniEMBWiFi image 2017-08-02T19:16:20+00:00 Mathias Kresin dev@kresin.me 2017-07-31T18:21:12+00:00 48798af6d224ae5c2e567be5b4ff88283ab9c208 Reference the Omnima MiniEMBWiFi device tree source file in the image build code. Otherwise the dts of the image processed before is used. Signed-off-by: Mathias Kresin <dev@kresin.me> 
Reference the Omnima MiniEMBWiFi device tree source file in the image
build code. Otherwise the dts of the image processed before is used.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: build HuaWei HG255D image 2017-08-02T19:16:20+00:00 Mathias Kresin dev@kresin.me 2017-07-31T18:19:14+00:00 1a050c83ac25b4c65b68f704fd70c9f90f4c25ed The code to build an image was disabled some time ago for unknown reasons albeit the image looks fine. Signed-off-by: Mathias Kresin <dev@kresin.me> 
The code to build an image was disabled some time ago for unknown
reasons albeit the image looks fine.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: fix Mercury MAC1200R v2.0 board name 2017-07-29T07:24:59+00:00 Mathias Kresin dev@kresin.me 2017-07-28T17:22:55+00:00 5e409f0e69ce77186f4e70dd9068e43dfc36a9bc With d2b6bf141662 ("ramips: fix image validation errors") the board name was changed to fix an image validation error. But this change wasn't applied to all other files using the board name, which broke sysupgrade. Revert this change and use the former board name in the metadata instead. Signed-off-by: Mathias Kresin <dev@kresin.me> 
With d2b6bf141662 ("ramips: fix image validation errors") the board
name was changed to fix an image validation error. But this change
wasn't applied to all other files using the board name, which broke
sysupgrade.

Revert this change and use the former board name in the metadata
instead.

Signed-off-by: Mathias Kresin <dev@kresin.me>
ramips: add om-watchdog to rut5xx DEVICE_PACKAGES 2017-05-15T20:56:01+00:00 Steffen Weinreich steve@weinreich.org 2017-04-25T14:44:39+00:00 4bd98e9224cfd89a2d8de5759a7823964d89225f Add om-watchdog as default package for rut5xx. Signed-off-by: Steffen Weinreich <steve@weinreich.org> 
Add om-watchdog as default package for rut5xx.

Signed-off-by: Steffen Weinreich <steve@weinreich.org>
ramips: add factory firmware for Tp-Link C20i/C50 2017-05-05T18:00:57+00:00 Henryk Heisig hyniu@o2.pl 2017-05-05T15:07:28+00:00 86196830371c07c2b5721002f2ad500ca893076e TP-Link firmware doesn't accept sysupgrade.bin with metadata. Signed-off-by: Henryk Heisig <hyniu@o2.pl> 
TP-Link firmware doesn't accept sysupgrade.bin with metadata.

Signed-off-by: Henryk Heisig <hyniu@o2.pl>