This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
doing so will sort all profiles alphabetically Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Andrew Yong <me@ndoo.sg>
https://wiki.openwrt.org/toh/netgear/wndr3700 wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49247
The WG3526 is the follow-up to the 2626 and is mostly the same, with the excaption that the mt7602 has been replaced with the mt7603. The internal wifi setup has also changed slightly. Based on my tests, everything that worked on the 2626 works on the 3526 and with roughly the same performance. v1->v2: * Remove some references to 2626 that I had missed in the dts. v2->v3: * Update patch to match new file structure. * Removed SD driver to be consistent with other MT7621 targets. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> SVN-Revision: 49213
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for months resulting in unbootable devices. Until it's fixed, disable it in the default profiles. Reports / Discussed here: https://dev.openwrt.org/ticket/21392 https://dev.openwrt.org/ticket/21834 https://dev.openwrt.org/ticket/21995 https://forum.openwrt.org/viewtopic.php?id=59092 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> SVN-Revision: 49131
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware). Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49127
Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49126
This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881