mtk-20170518/target/linux/ramips/mt7621/profiles, branch reboot MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ramips: Add support for the Netgear WNDR3700v5 2016-04-26T11:43:53+00:00 John Crispin john@openwrt.org 2016-04-26T11:43:53+00:00 cb049e71cdc08e17f664403a0ef970c480ae5c4a https://wiki.openwrt.org/toh/netgear/wndr3700 wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49247 
https://wiki.openwrt.org/toh/netgear/wndr3700

wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>

SVN-Revision: 49247
ramips: Add support for ZBT WG3526 2016-04-21T19:47:08+00:00 John Crispin john@openwrt.org 2016-04-21T19:47:08+00:00 30fbc1a4d146ae0060d02946709fd6d8cc2a2b56 The WG3526 is the follow-up to the 2626 and is mostly the same, with the excaption that the mt7602 has been replaced with the mt7603. The internal wifi setup has also changed slightly. Based on my tests, everything that worked on the 2626 works on the 3526 and with roughly the same performance. v1->v2: * Remove some references to 2626 that I had missed in the dts. v2->v3: * Update patch to match new file structure. * Removed SD driver to be consistent with other MT7621 targets. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> SVN-Revision: 49213 
The WG3526 is the follow-up to the 2626 and is mostly the same, with the
excaption that the mt7602 has been replaced with the mt7603. The internal wifi
setup has also changed slightly. Based on my tests, everything that worked on
the 2626 works on the 3526 and with roughly the same performance.

v1->v2:
* Remove some references to 2626 that I had missed in the dts.

v2->v3:
* Update patch to match new file structure.
* Removed SD driver to be consistent with other MT7621 targets.

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>

SVN-Revision: 49213
ramips: Disable the SD driver by default on MT7621 2016-04-09T10:25:03+00:00 John Crispin john@openwrt.org 2016-04-09T10:25:03+00:00 8b8dfeb027c820c7264b7ffb724d58911bf8ae42 The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for months resulting in unbootable devices. Until it's fixed, disable it in the default profiles. Reports / Discussed here: https://dev.openwrt.org/ticket/21392 https://dev.openwrt.org/ticket/21834 https://dev.openwrt.org/ticket/21995 https://forum.openwrt.org/viewtopic.php?id=59092 Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net> SVN-Revision: 49131 
The SD driver has been a long and dragging issue on the MT7621 platforms as it hasn't worked for
months resulting in unbootable devices. Until it's fixed, disable it in the default profiles.

Reports / Discussed here:

https://dev.openwrt.org/ticket/21392
https://dev.openwrt.org/ticket/21834
https://dev.openwrt.org/ticket/21995
https://forum.openwrt.org/viewtopic.php?id=59092

Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>

SVN-Revision: 49131
ramips: mt7621: fix Ubiquiti EdgeRouter X profile 2016-04-09T10:24:47+00:00 John Crispin john@openwrt.org 2016-04-09T10:24:47+00:00 e626a0d877002c71299a22d57c572f84295760ce Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware). Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49127 
Remove unnecessary packages to reduce image size so it fits in initramfs (to enable upgrading from factory firmware).

Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49127
ramips: mt7621: sync MQmaker WiTi profile name to dts name 2016-04-09T10:24:44+00:00 John Crispin john@openwrt.org 2016-04-09T10:24:44+00:00 37f1022d737dc3cc3bb11e1c36c643bc81eb0552 Signed-off-by: Roman Yeryomin <roman@advem.lv> SVN-Revision: 49126 
Signed-off-by: Roman Yeryomin <roman@advem.lv>

SVN-Revision: 49126
ramips: add support for Ubiquiti EdgeRouter X (UBNT-ERX) 2015-12-12T07:38:06+00:00 John Crispin john@openwrt.org 2015-12-12T07:38:06+00:00 4e31b2e8697c21f9bd6493bb3d78a4a41c6a9a52 This router is based on MT7621 SoC, no wifi, no usb, nand. Works: * Boots. * Ethernet. * Switch. * Button (reset). * Flashing OpenWrt from stock firmware. * Upgrading OpenWrt. Doesn't work: * No GPIO leds. All leds are controlled by switch, but stock firmware was able to control them. * SoC has crypto engine but no open driver. * SoC has nat acceleration, but no open driver. * This router has 2MB spi flash soldered in but MT nand/spi drivers do not support pin sharing, so it is not accessable and disabled. Stock firmware could read it and it was empty. * PoE out. Router has serial pins populated. If looking at the top of the router, then counting from Eth sockets pins go as: 'GND, RX, TX, GND'. 3.3v, 57600. U-boot bootloader supports tftpboot, controlled from serial. This router has two kernel partitions: 'live' and 'backup'. They are swapped during flashing (on both stock and OpenWrt). Active partition is controlled by a flag in a factory partition. U-boot has custom command to switch active kernel partition. Kernel partitions are 'bare flash' 3MB. Stock bootloader has no UBI support. Stock rootfs is UBIFS. Flashing procedure. Stock firmware uses custom kernel patch to mount squashfs from a file that is located on UBIFS volume. This makes wiping out this volume from within stock firmware difficult. Instead this patch builds image that is flashable by stock firmware and contains initrams image (with minimal set of packages to fit into kernel partition). Once this is flashed one can reboot into initramfs OpenWrt and use sysupgrade to flash OpenWrt including rootfs into nand. Note: factory image is only built if initramfs image is enabled. Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com> SVN-Revision: 47881 
This router is based on MT7621 SoC, no wifi, no usb, nand.

Works:
* Boots.
* Ethernet.
* Switch.
* Button (reset).
* Flashing OpenWrt from stock firmware.
* Upgrading OpenWrt.

Doesn't work:
* No GPIO leds. All leds are controlled by switch,
  but stock firmware was able to control them.
* SoC has crypto engine but no open driver.
* SoC has nat acceleration, but no open driver.
* This router has 2MB spi flash soldered in but MT
  nand/spi drivers do not support pin sharing,
  so it is not accessable and disabled. Stock
  firmware could read it and it was empty.
* PoE out.

Router has serial pins populated. If looking at the top
of the router, then counting from Eth sockets pins go as:
'GND, RX, TX, GND'. 3.3v, 57600.

U-boot bootloader supports tftpboot, controlled from serial.
This router has two kernel partitions: 'live' and 'backup'.
They are swapped during flashing (on both stock and OpenWrt).
Active partition is controlled by a flag in a factory partition.
U-boot has custom command to switch active kernel partition.
Kernel partitions are 'bare flash' 3MB. Stock bootloader has
no UBI support. Stock rootfs is UBIFS.

Flashing procedure.
Stock firmware uses custom kernel patch to mount squashfs
from a file that is located on UBIFS volume. This makes wiping
out this volume from within stock firmware difficult.
Instead this patch builds image that is flashable by stock firmware
and contains initrams image (with minimal set of packages
to fit into kernel partition). Once this is flashed one can reboot
into initramfs OpenWrt and use sysupgrade to flash OpenWrt including
rootfs into nand.
Note: factory image is only built if initramfs image is enabled.

Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>

SVN-Revision: 47881
ramips: add additional support for MQmaker WiTi board 2015-12-11T15:04:13+00:00 John Crispin john@openwrt.org 2015-12-11T15:04:13+00:00 9f14006809f6122d68e22394d147e6fe4a47e676 The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram, 2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and one 5 ghz antenna. This is the 6th submission that adds support for XHCI in the device tree file, along with switching the location of the 2 radio's and addition of the kmod-i2c-mt7621 in the default packages of the profile. Signed-off-by: Sebastian Careba <nitroshift@yahoo.com> SVN-Revision: 47845 
The board is based on mt7621AT cpu, and has 16mb nor flash, 256mb of ram,
2 sata ports, microsd card slot, 1 USB 3.0 port and at least one 2.4 and
one 5 ghz antenna.

This is the 6th submission that adds support for XHCI in the device tree
file, along with switching the location of the 2 radio's and addition of
the kmod-i2c-mt7621 in the default packages of the profile.

Signed-off-by: Sebastian Careba <nitroshift@yahoo.com>

SVN-Revision: 47845
ralink: add support for netis WF-2881 2015-11-24T18:29:26+00:00 John Crispin john@openwrt.org 2015-11-24T18:29:26+00:00 8c1f5141ceee722cdd282f909390b73455968cfd netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN. It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0. The following patch adds support for this device. this device only works on top of UBI. Tested and working: * ethernet * both WiFi radios * USB 3.0 * buttons (reset button) * ethernet switch and USB diag LEDs * UART * GPIOs * sysupgrade Tested and not working * failsafe Signed-off-by: YounJae Rho <luxflow@live.com> SVN-Revision: 47619 
netis WF-2881 is an MT7621AT based router with MT7602EN, MT7612EN.
It has 128MB DDR3, 128MB SLC NAND FLASH, 5-port Gbps switch and 1x USB 3.0.
The following patch adds support for this device.

this device only works on top of UBI.

Tested and working:
* ethernet
* both WiFi radios
* USB 3.0
* buttons (reset button)
* ethernet switch and USB diag LEDs
* UART
* GPIOs
* sysupgrade

Tested and not working
* failsafe

Signed-off-by: YounJae Rho <luxflow@live.com>

SVN-Revision: 47619
ramips: minor fixes for mt7621 profiles 2015-11-07T12:51:48+00:00 Felix Fietkau nbd@openwrt.org 2015-11-07T12:51:48+00:00 b95aed986a130d3e51f96a7c0b81e4843a33edcf * remove references to non-existing kmod-usb3-mt7621 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!) Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47407 
* remove references to non-existing kmod-usb3-mt7621
 * ZTB WG2626 doesn't have an RTC (thanks to Piotr Dymacz!)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47407
ramips: add support for ZBT WG2626 2015-11-02T10:18:19+00:00 John Crispin john@openwrt.org 2015-11-02T10:18:19+00:00 165244a222bf466bd952bac38de1cbdd53a80113 Signed-off-by: Daniel Golle <daniel@makrotopia.org> SVN-Revision: 47351 
Signed-off-by: Daniel Golle <daniel@makrotopia.org>

SVN-Revision: 47351