mtk-20170518/target, branch master

kernel: add missing symbol

2018-09-10T15:50:40+00:00

Signed-off-by: John Crispin

ramips: Fix early memory calculation for certain MIPS platforms

2018-09-10T08:07:42+00:00

Kernel upstream commit 67a3ba25aa95 ("MIPS: Fix incorrect mem=X@Y handling") introduced a new issue for rt288x where "PHYS_OFFSET" is 0x0 but the calculated "ramstart" is not. As the prerequisite of custom memory map has been removed, this results in the full memory range of 0x0 - 0x8000000 to be marked as reserved
for this platform.

This patch adds the originally intended prerequisite again.

Signed-off-by: Tobias Wolf

ath79: ubnt-xm: add rssileds package

2018-09-10T07:58:31+00:00

In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM family.

Signed-off-by: Lech Perczak

ath79: ubnt-xm: create RSSI monitor on wlan0

2018-09-10T07:58:31+00:00

When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti XM family, the mapping for rssileds monitor was omitted
by mistake. Therefore create the mapping, so RSSI LEDs work without
additional configuration, after starting rssileds service.

Signed-off-by: Lech Perczak

ath79: add support for Buffalo WZR-HP-AG300H

2018-09-10T07:35:07+00:00

Buffalo WZR-HP-AG300H is a dual band router based on
Qualcom Atheros AR7161 rev 2

Specification:
- 680 MHz CPU (Qualcomm Atheros AR7161)
- 128 MiB RAM (2x Samsung K4H511638G-LCCC)
- 32 MiB Flash (2x Winbond 25Q128BVFG)
- WiFi 5 GHz a/n (Atheros AR9220)
- WiFi 2.4 GHz b/g/n (Atheros AR9223)
- 1000Base-T WAN (Atheros AR7161)
- 4x 1000Base-T Switch (Atheros AR8316)
- 1x USB 2.0
- 3 Buttons (AOSS/WPS, Reset, USB Eject)
- 2 Slide switches (Router (on/off/auto), Movie Engine (on/off))
- 9 LEDs (Power green, WLAN 2GHz green, WLAN 2GHz amber,
    WLAN 5GHz green, WLAN 5GHz LED amber, Router green,
    Diag red, Movie Engine blue, USB green)

It is already supported by the ar71xx target.

For more information on the device visit the wiki:


Serial console:
- The UART Header is next to Movie Engine Switch.
- Pinout is RX - TX - GND - 3.3V (Square Pad is 3.3V)
- The Serial setting is 115200-8-N-1.

Installation of OpenWRT from vendor firmware:
- Connect to the Web-interface at http://192.168.11.1
- Go to “Administration” → “Firmware Upgrade”
- Upload the OpenWrt factory image

Tested:
- Ethernet (LAN, WAN)
- WiFi
- Installation
  - via TFTP rescue
  - via factory image
    - on firmware v1.77 (28-05-2012)
    - on pro firmware v24SP2 r30356 (26-03-2018)
  - via sysupgrade from ar71xx
    (wlan devices don't work because of new names)
  - via sysupgrade from itself
- Buttons
- LEDS
- USB (Power control and device recognition)

Signed-off-by: Bernhard Frauendienst

kernel: add driver for virtual mtd_concat devices

2018-09-10T07:35:07+00:00

Some systems require multiple flash chips to be concatenated and read as
a single mtd device. The ar71xx target provides custom code to create
such mtdconcat devices. When porting devices to ath79, however, there is
no way to create such devices from within the device tree.

This commit adds a driver for creating virtual mtd-concat devices to the
ath79 target. Nodes must have a compatible = "virtual,mtd-concat" line,
and define a list of devices to concat in the 'devices' property,
for example:

flash {
	compatible = "virtual,mtd-concat";

	devices = <&flash0 &flash1>;
};

The driver is added to the very end of the mtd Makefile to increase the
likelyhood of all child devices already being loaded at the time of
probing, preventing unnecessary deferred probes which might in turn
cause other problems (like failure to load MAC addresses from art because
the partitions are not loaded yet).

Signed-off-by: Bernhard Frauendienst

ath79: add support for ELECOM WRC-300GHBK2-I

2018-09-10T07:30:28+00:00

ELECOM WRC-300GHBK2-I is a 2.4 GHz wireless router, based on Qualcomm
Atheros QCA9563.

Specification:

- Qualcomm Atheros QCA9563
- 64 MB of RAM (DDR2)
- 8 MB of Flash (SPI-NOR)
- 2T2R 2.4 GHz wifi
  - SoC internal
- 5x 10/100/1000 Mbps Ethernet
- 3x LEDs, 4x keys(connected to GPIO: 3x)
- UART header on PCB
  - TX, GND, RX, Vcc from ethernet port side
  - 115200n8

Flash instruction using factory image:

1. Boot the WRC-300GHBK2-I normaly and connect the computer to its
LAN port
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新 手動更新（アップデート）")
3. Select the OpenWrt factory image and click apply ("適用") button
to perform firmware update
4. On the (initramfs) factory image, execute "mtd erase firmware" to
erase stock firmware and execute sysupgrade with squashfs-sysupgrade
image for WRC-300GHBK2-I
5. Wait ~150 seconds to complete flashing

Signed-off-by: INAGAKI Hiroshi

kernel: backport i2c-gpio working over slow can_sleep GPIOs

2018-09-10T07:28:55+00:00

Signed-off-by: Martin Schiller

kernel: backport rtc ds1308 support to 4.9

2018-09-10T07:19:44+00:00

Signed-off-by: Martin Schiller

mvebu: Replace RTC initialization patch with upstreamed version

2018-09-10T07:11:31+00:00

While we're at it, rename the patches to their proper git format-patch
name.

Tested on a Turris Omnia.

Signed-off-by: Rosen Penev