mtk-20170518/tools/firmware-utils/src, branch v18.06.0-rc2 MTK 20170518 : Mediatek SDK based on OpenWRT Barrier Breaker ar71xx: Add support for TP-Link CPE210 v2 2018-06-23T14:08:22+00:00 Adrian Schmutzler freifunk@adrianschmutzler.de 2018-01-19T13:45:42+00:00 286a456319a1ec5cb54bf30defa5c8efd4a667cf This PR adds support for a popular low-cost 2.4GHz N based AP Specifications: - SoC: Qualcomm Atheros QCA9533 (650MHz) - RAM: 64MB - Storage: 8 MB SPI NOR - Wireless: 2.4GHz N based built into SoC 2x2 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN Installation: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 4-5 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP adress:192.168.0.254 Notes: TP-Link does not use bootstrap registers so without this patch reference clock detects as 40MHz while it is actually 25MHz. This is due to messed up bootstrap resistor configuration on the PCB. Provided GPL code just forces 25MHz reference clock. That causes booting with completely wrong clocks, for example, CPU tries to boot at 1040MHz while the stock is 650MHz. So this PR depends on PR #672 to remove 40MHz reference clock. Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> (cherry picked from commit 5c5bf8b8658a588423f6ec445d7ef6a36f99a396) 
This PR adds support for a popular low-cost 2.4GHz N based AP

Specifications:
 - SoC: Qualcomm Atheros QCA9533 (650MHz)
 - RAM: 64MB
 - Storage: 8 MB SPI NOR
 - Wireless: 2.4GHz N based built into SoC 2x2
 - Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN

Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254

Notes:
TP-Link does not use bootstrap registers so without this patch reference
clock detects as 40MHz while it is actually 25MHz.
This is due to messed up bootstrap resistor configuration on the PCB.
Provided GPL code just forces 25MHz reference clock.
That causes booting with completely wrong clocks, for example, CPU tries
to boot at 1040MHz while the stock is 650MHz.
So this PR depends on PR #672 to remove 40MHz reference clock.
Thanks to Sven Eckelmann <sven@narfation.org> for properly patching that.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 5c5bf8b8658a588423f6ec445d7ef6a36f99a396)
ar71xx: add support for TP-LINK Archer C7 v5 2018-06-21T05:02:51+00:00 Arvid E. Picciani aep@exys.org 2018-04-16T11:18:37+00:00 4e9fa569b0279c81aa9ca96a6669bc08115d4227 TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros QCA9563+QCA9880. Specification: - 750/400/250 MHz (CPU/DDR/AHB - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 3T3R 5 GHz - 5x 10/100/1000 Mbps Ethernet - 10x LED, 2x button - UART header on PCB Flash instruction: 1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface Flash instruction using TFTP recovery: 1. Set PC to fixed ip address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin and rename it to ArcherC7v5_tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold Reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery. Signed-off-by: Arvid E. Picciani <aep@exys.org> (cherry picked from commit bf39d5594b3c8f9409e6d9408a1f370c9f18d0dd) 
TP-Link Archer C7 v5 is a dual-band AC1750 router, based on Qualcomm/Atheros
QCA9563+QCA9880.

Specification:

- 750/400/250 MHz (CPU/DDR/AHB
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 3T3R 5 GHz
- 5x 10/100/1000 Mbps Ethernet
- 10x LED, 2x button
- UART header on PCB

Flash instruction:
1. Upload lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin via Web interface

Flash instruction using TFTP recovery:
1. Set PC to fixed ip address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c7-v5-squashfs-factory.bin
and rename it to ArcherC7v5_tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.

Signed-off-by: Arvid E. Picciani <aep@exys.org>
(cherry picked from commit bf39d5594b3c8f9409e6d9408a1f370c9f18d0dd)
ipq806x: increase kernel partition size for the TP-Link Archer C2600 2018-05-24T15:24:31+00:00 Stefan Lippers-Hollmann s.l-h@gmx.de 2018-05-18T01:10:18+00:00 742ac017baaa7de2fde04bf6cdd39c0e9e5f92e0 The default image does not fit 2 MB anymore, expand os-image partition to 4 MB. Upgrading works transparently via sysupgrade in both directions. Another option would have been to merge "os-image" and "rootfs" into a single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just changing the sizes of the existing partitioning has been deemed safer and actually tested on an affected device; the maximum for rootfs changes from 27 MB to 25 MB. Run-tested on TP-Link Archer C2600. Signed-off-by: Joris de Vries <joris@apptrician.nl> [slh: extend comments and commit message, rename rootfs] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> (cherry picked from commit b72b36653a3fc8347456ab9c45d26a3144688a4c) 
The default image does not fit 2 MB anymore, expand os-image partition
to 4 MB.

Upgrading works transparently via sysupgrade in both directions.
Another option would have been to merge "os-image" and "rootfs" into a
single "firmware" partition using MTD_SPLIT_TPLINK_FW, but just
changing the sizes of the existing partitioning has been deemed safer
and actually tested on an affected device; the maximum for rootfs
changes from 27 MB to 25 MB.

Run-tested on TP-Link Archer C2600.

Signed-off-by: Joris de Vries <joris@apptrician.nl>
[slh: extend comments and commit message, rename rootfs]
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>

(cherry picked from commit b72b36653a3fc8347456ab9c45d26a3144688a4c)
firmware-utils: add DNS-313 image header tool 2018-05-05T04:57:00+00:00 Linus Walleij linus.walleij@linaro.org 2018-04-04T20:15:29+00:00 20d0dace40b74b098309cefb29a1ce5d57988e7e This tool is used to create headers on images for the D-Link DNS-313 in gemini target. Will be used after switching gemini to 4.14 kernel. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> 
This tool is used to create headers on images for the
D-Link DNS-313 in gemini target.
Will be used after switching gemini to 4.14 kernel.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
firmware-utils: tplink-safeloader: increase RE350 kernel size 2018-04-23T20:07:22+00:00 Alex Maclean monkeh@monkeh.net 2018-04-23T17:36:54+00:00 a31107a97a00b2d637b8f7468f01317332dad801 4.14 increased kernel size, so grow the kernel partition by 128K to compensate. Fixes FS#1479. Signed-off-by: Alex Maclean <monkeh@monkeh.net> 
4.14 increased kernel size, so grow the kernel partition by 128K to compensate.

Fixes FS#1479.

Signed-off-by: Alex Maclean <monkeh@monkeh.net>
ar71xx: increase kernel partition size for CPE/WBS 210/510 2018-04-10T16:29:19+00:00 Matthias Schiffer mschiffer@universe-factory.net 2018-04-10T16:14:41+00:00 e39847ea2f70bf8880a4533b22a0eed110ffea98 Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> 
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
firmware-utils: tplink-safeloader: move CPE/WBS 210/510 version metainfo to the end 2018-04-10T16:29:19+00:00 Matthias Schiffer mschiffer@universe-factory.net 2018-04-10T15:26:34+00:00 373dc11b519516682ab48bf7db501ffffced4e61 Having the metainfo between kernel and rootfs prevents us from resizing the kernel partition as necessary. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> 
Having the metainfo between kernel and rootfs prevents us from resizing
the kernel partition as necessary.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
ar71xx: add support for TP-Link Archer C60 v2 2018-04-06T22:09:05+00:00 Henryk Heisig hyniu@o2.pl 2018-01-15T05:44:14+00:00 c0742307a18178ee7d2cee1fc6b0e199ccb1e1fa TP-Link Archer C60 v2 is a dual-band AC1350 router, based on Qualcomm/Atheros QCA9561 + QCA9886. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 7x LED, 2x button - UART header on PCB Flash instruction (web): Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use OEM System Tools - Firmware Upgrade site. Flash instruction (recovery): 1. Set PC to fixed IP address 192.168.0.66 2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and rename it to tp_recovery.bin 3. Start a tftp server with the file tp_recovery.bin in its root directory 4. Turn off the router 5. Press and hold reset button 6. Turn on router with the reset button pressed and wait ~15 seconds 7. Release the reset button and after a short time the firmware should be transferred from the tftp server 8. Wait ~30 second to complete recovery Flash instruction (under U-Boot, using UART): tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin erase 0x9f030000 +$filesize cp.b $fileaddr 0x9f030000 $filesize reset Signed-off-by: Henryk Heisig <hyniu@o2.pl> 
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.

Specification:

- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB

Flash instruction (web):

Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.

Flash instruction (recovery):

1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
   rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
   directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
   be transferred from the tftp server
8. Wait ~30 second to complete recovery

Flash instruction (under U-Boot, using UART):

tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset

Signed-off-by: Henryk Heisig <hyniu@o2.pl>
firmware-utils: image generator for D-Link DAP-1330 2018-04-05T13:28:56+00:00 Nicolò Veronese nicveronese@gmail.com 2017-06-16T12:06:07+00:00 0d8a0a6a17ea203527a5c61241ea19d763aed567 Signed-off-by: Nicolò Veronese <nicveronese@gmail.com> 
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
firmware-utils: add JBOOT bootloader image support 2018-03-18T21:22:38+00:00 Pawel Dembicki paweldembicki@gmail.com 2018-02-03T11:59:50+00:00 84c1b786b9830c17034e5de915ce11965666febd Tested on D-Link DWR-116. Based on mktplinkfw. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> 
Tested on D-Link DWR-116.
Based on mktplinkfw.

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>