diff options
9 files changed, 484 insertions, 7 deletions
diff --git a/target/linux/ipq806x/base-files/etc/board.d/01_leds b/target/linux/ipq806x/base-files/etc/board.d/01_leds index a8d9573..fea4d7c 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq806x/base-files/etc/board.d/01_leds @@ -15,6 +15,11 @@ compex,wpq864) ucidef_set_led_usbport "usb" "USB" "wpq864:green:usb" "usb1-port1" "usb2-port1" ucidef_set_led_usbport "pcie-usb" "PCIe USB" "wpq864:green:usb-pcie" "usb3-port1" ;; +nec,wg2600hp) + ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:green:wlan2g" "phy1tpt" + ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:green:wlan5g" "phy0tpt" + ucidef_set_led_switch "wan" "WAN" "${boardname}:green:active" "switch0" "0x1e" + ;; netgear,d7800 |\ netgear,r7500 |\ netgear,r7500v2 |\ diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index 9d8af44..f5daf62 100755 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -29,6 +29,10 @@ linksys,ea8500) ucidef_set_interface_macaddr "lan" "$hw_mac_addr" ucidef_set_interface_macaddr "wan" "$hw_mac_addr" ;; +nec,wg2600hp) + ucidef_add_switch "switch0" \ + "2:lan" "3:lan" "4:lan" "5:lan" "6@eth1" "1:wan" "0@eth0" + ;; qcom,ipq8064-db149) ucidef_set_interface_lan "eth1 eth2 eth3" ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index ed99bd5..fa49c25 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -60,6 +60,7 @@ case "$FIRMWARE" in ath10kcal_extract "radio" 4096 12064 # ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -1) ;; + nec,wg2600hp |\ tplink,vr2600v) ath10kcal_extract "ART" 4096 12064 ;; @@ -83,6 +84,7 @@ case "$FIRMWARE" in ath10kcal_extract "radio" 20480 12064 # ath10kcal_patch_mac $(macaddr_add $(mtd_get_mac_binary default-mac 8) -2) ;; + nec,wg2600hp |\ tplink,vr2600v) ath10kcal_extract "ART" 20480 12064 ;; diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 7e31c38..afa425f 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -15,6 +15,9 @@ case "$board" in linksys,ea8500) echo $(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) $(($PHYNBR + 1)) ) > /sys${DEVPATH}/macaddress ;; + nec,wg2600hp) + echo $(macaddr_add $(mtd_get_mac_binary PRODUCTDATA 12) $((1 - $PHYNBR)) ) > /sys${DEVPATH}/macaddress + ;; netgear,d7800 |\ netgear,r7500v2 |\ netgear,r7800) diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 4f230ea..b41bea1 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -32,6 +32,7 @@ platform_do_upgrade() { MTD_CONFIG_ARGS="-s 0x200000" default_do_upgrade "$ARGV" ;; + nec,wg2600hp |\ *) default_do_upgrade "$ARGV" ;; diff --git a/target/linux/ipq806x/config-4.14 b/target/linux/ipq806x/config-4.14 index d64e406..fda8f52 100644 --- a/target/linux/ipq806x/config-4.14 +++ b/target/linux/ipq806x/config-4.14 @@ -309,6 +309,7 @@ CONFIG_MTD_QCOM_SMEM_PARTS=y CONFIG_MTD_SPI_NOR=y CONFIG_MTD_SPLIT_FIRMWARE=y CONFIG_MTD_SPLIT_FIT_FW=y +CONFIG_MTD_SPLIT_UIMAGE_FW=y CONFIG_MTD_UBI=y CONFIG_MTD_UBI_BEB_LIMIT=20 CONFIG_MTD_UBI_BLOCK=y diff --git a/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts new file mode 100644 index 0000000..b643014 --- /dev/null +++ b/target/linux/ipq806x/files-4.14/arch/arm/boot/dts/qcom-ipq8064-wg2600hp.dts @@ -0,0 +1,448 @@ +#include "qcom-ipq8064-v2.0.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "NEC Aterm WG2600HP"; + compatible = "nec,wg2600hp", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x1e000000>; + device_type = "memory"; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + rsvd@41200000 { + reg = <0x41200000 0x300000>; + no-map; + }; + }; + + aliases { + serial0 = &gsbi4_serial; + mdio-gpio0 = &mdio0; + + led-boot = &power_green; + led-failsafe = &power_green; + led-running = &power_green; + led-upgrade = &power_green; + }; + + chosen { + linux,stdout-path = "serial0:115200n8"; + }; + + soc { + pinmux@800000 { + button_pins: button_pins { + mux { + pins = "gpio16", "gpio54", "gpio24", "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + i2c4_pins: i2c4_pinmux { + mux { + pins = "gpio12", "gpio13"; + function = "gsbi4"; + drive-strength = <12>; + bias-disable; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio6", "gpio7", "gpio8", "gpio9", "gpio14", + "gpio15", "gpio55", "gpio56", "gpio57", "gpio58", + "gpio64", "gpio65"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + bias-pull-down; + }; + + data { + pins = "gpio18", "gpio19"; + drive-strength = <10>; + }; + + cs { + pins = "gpio20"; + drive-strength = <10>; + bias-pull-up; + }; + + clk { + pins = "gpio21"; + drive-strength = <12>; + }; + }; + + mdio0_pins: mdio0_pins { + mux { + pins = "gpio0", "gpio1"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + }; + + usb_pwr_en_pins: usb_pwr_en_pins { + mux { + pins = "gpio22"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + output-high; + }; + }; + }; + + gsbi@16300000 { + qcom,mode = <GSBI_PROT_I2C_UART>; + status = "ok"; + serial@16340000 { + status = "ok"; + }; + /* + * The i2c device on gsbi4 should not be enabled. + * On ipq806x designs gsbi4 i2c is meant for exclusive + * RPM usage. Turning this on in kernel manifests as + * i2c failure for the RPM. + */ + }; + + gsbi5: gsbi@1a200000 { + qcom,mode = <GSBI_PROT_SPI>; + status = "ok"; + + spi4: spi@1a280000 { + status = "ok"; + + pinctrl-0 = <&spi_pins>; + pinctrl-names = "default"; + + cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; + + flash: m25p80@0 { + compatible = "jedec,spi-nor"; + #address-cells = <1>; + #size-cells = <1>; + spi-max-frequency = <50000000>; + reg = <0>; + + SBL1@0 { + label = "SBL1"; + reg = <0x0 0x20000>; + read-only; + }; + + MIBIB@20000 { + label = "MIBIB"; + reg = <0x20000 0x20000>; + read-only; + }; + + SBL2@40000 { + label = "SBL2"; + reg = <0x40000 0x40000>; + read-only; + }; + + SBL3@80000 { + label = "SBL3"; + reg = <0x80000 0x80000>; + read-only; + }; + + DDRCONFIG@100000 { + label = "DDRCONFIG"; + reg = <0x100000 0x10000>; + read-only; + }; + + SSD@110000 { + label = "SSD"; + reg = <0x110000 0x10000>; + read-only; + }; + + TZ@120000 { + label = "TZ"; + reg = <0x120000 0x80000>; + read-only; + }; + + RPM@1a0000 { + label = "RPM"; + reg = <0x1a0000 0x80000>; + read-only; + }; + + APPSBL@220000 { + label = "APPSBL"; + reg = <0x220000 0x80000>; + read-only; + }; + + APPSBLENV@2a0000 { + label = "APPSBLENV"; + reg = <0x2a0000 0x10000>; + }; + + PRODUCTDATA: PRODUCTDATA@2b0000 { + label = "PRODUCTDATA"; + reg = <0x2b0000 0x30000>; + read-only; + }; + + ART@2e0000 { + label = "ART"; + reg = <0x2e0000 0x40000>; + read-only; + }; + + TP@320000 { + label = "TP"; + reg = <0x320000 0x40000>; + read-only; + }; + + TINY@360000 { + label = "TINY"; + reg = <0x360000 0x500000>; + read-only; + }; + + firmware@860000 { + label = "firmware"; + reg = <0x860000 0x17a0000>; + }; + }; + }; + }; + + phy@100f8800 { /* USB3 port 1 HS phy */ + status = "ok"; + }; + + phy@100f8830 { /* USB3 port 1 SS phy */ + status = "ok"; + }; + + phy@110f8800 { /* USB3 port 0 HS phy */ + status = "ok"; + }; + + phy@110f8830 { /* USB3 port 0 SS phy */ + status = "ok"; + }; + + usb30@0 { + status = "ok"; + + pinctrl-0 = <&usb_pwr_en_pins>; + pinctrl-names = "default"; + }; + + usb30@1 { + status = "ok"; + }; + + pcie0: pci@1b500000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + }; + + pcie1: pci@1b700000 { + status = "ok"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + force_gen1 = <1>; + }; + + mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0x6a545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + >; + }; + + phy4: ethernet-phy@4 { + device_type = "ethernet-phy"; + reg = <4>; + }; + }; + + gmac1: ethernet@37200000 { + status = "ok"; + phy-mode = "rgmii"; + qcom,id = <1>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + mtd-mac-address = <&PRODUCTDATA 6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + gmac2: ethernet@37400000 { + status = "ok"; + phy-mode = "sgmii"; + qcom,id = <2>; + + mtd-mac-address = <&PRODUCTDATA 0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>; + linux,code = <KEY_WPS_BUTTON>; + }; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = <KEY_RESTART>; + }; + + bridge { + label = "bridge"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + linux,input-type = <EV_SW>; + }; + + converter { + label = "converter"; + gpios = <&qcom_pinmux 25 GPIO_ACTIVE_LOW>; + linux,code = <BTN_0>; + linux,input-type = <EV_SW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + converter_green { + label = "wg2600hp:green:converter"; + gpios = <&qcom_pinmux 6 GPIO_ACTIVE_HIGH>; + }; + + power_red { + label = "wg2600hp:red:power"; + gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; + }; + + active_green { + label = "wg2600hp:green:active"; + gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; + }; + + active_red { + label = "wg2600hp:red:active"; + gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; + }; + + power_green: power_green { + label = "wg2600hp:green:power"; + gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>; + }; + + converter_red { + label = "wg2600hp:red:converter"; + gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_green { + label = "wg2600hp:green:wlan2g"; + gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>; + }; + + wlan2g_red { + label = "wg2600hp:red:wlan2g"; + gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; + }; + + wlan5g_green { + label = "wg2600hp:green:wlan5g"; + gpios = <&qcom_pinmux 57 GPIO_ACTIVE_HIGH>; + }; + + wlan5g_red { + label = "wg2600hp:red:wlan5g"; + gpios = <&qcom_pinmux 58 GPIO_ACTIVE_HIGH>; + }; + + tv_green { + label = "wg2600hp:green:tv"; + gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>; + }; + + tv_red { + label = "wg2600hp:red:tv"; + gpios = <&qcom_pinmux 65 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&adm_dma { + status = "ok"; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index ac57991..2902af3 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -101,6 +101,18 @@ define Device/linksys_ea8500 endef TARGET_DEVICES += linksys_ea8500 +define Device/nec_wg2600hp + $(call Device/LegacyImage) + DEVICE_DTS := qcom-ipq8064-wg2600hp + BLOCKSIZE := 64k + BOARD_NAME := wg2600hp + DEVICE_TITLE := NEC Aterm WG2600HP + IMAGES := sysupgrade.bin + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca99x0 +endef +TARGET_DEVICES += nec_wg2600hp + define Device/netgear_d7800 $(call Device/DniImage) DEVICE_DTS := qcom-ipq8064-d7800 diff --git a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch index fead994..59f37a7 100644 --- a/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-4.14/0069-arm-boot-add-dts-files.patch @@ -10,19 +10,20 @@ Signed-off-by: John Crispin <john@phrozen.org> --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -699,6 +699,15 @@ dtb-$(CONFIG_ARCH_QCOM) += \ - qcom-apq8084-mtp.dtb \ - qcom-ipq4019-ap.dk01.1-c1.dtb \ - qcom-ipq8064-ap148.dtb \ +@@ -699,6 +699,16 @@ dtb-$(CONFIG_ARCH_QCOM) += \ + qcom-apq8084-mtp.dtb \ + qcom-ipq4019-ap.dk01.1-c1.dtb \ + qcom-ipq8064-ap148.dtb \ + qcom-ipq8064-c2600.dtb \ + qcom-ipq8064-d7800.dtb \ + qcom-ipq8064-db149.dtb \ + qcom-ipq8064-ea8500.dtb \ + qcom-ipq8064-r7500.dtb \ + qcom-ipq8064-r7500v2.dtb \ ++ qcom-ipq8064-wg2600hp.dtb \ + qcom-ipq8064-wpq864.dtb \ + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ - qcom-msm8660-surf.dtb \ - qcom-msm8960-cdp.dtb \ - qcom-msm8974-lge-nexus5-hammerhead.dtb \ + qcom-msm8660-surf.dtb \ + qcom-msm8960-cdp.dtb \ + qcom-msm8974-lge-nexus5-hammerhead.dtb \ |