| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC
Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1000Mhz
- Flash-Chip: Hynix NAND
- Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16
- RAM: 256MB
- LAN: 1x 1000 Mbps Ethernet
- WiFi: none
- 3x USB 2.0
- UART: for serial console
Installation instructions - easy steps:
1. download factory.bin and copy into tftp server
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
setenv serverip 192.168.1.1
setenv ipaddr 192.168.1.13
tftpboot 0x00800000 factory.bin
nand erase 0x100000 $(filesize)
nand write 0x00800000 0x100000 $(filesize)
run bootcmd
```
3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Installation steps nand bad blocks proof:
1. download initramfs-uImage and copy into usb ext2 partition
```
mkfs.ext2 -L ext2 /dev/sdh1
mount -t ext2 /dev/sdh1 /mnt
cp initramfs-uImage /mnt/initramfs.bin
umount /mnt
```
2. access uboot environment with serial cable and run
```
setenv mainlineLinux yes
setenv arcNumber 1682
setenv console 'console=ttyS0,115200n8'
setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
setenv bootargs_root 'root='
setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
saveenv
usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000
```
3. log into openwrt and sysupgrade to install into flash
```
sysupgrade -n /tmp/sysupgrade.bin
```
4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13)
Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
|
|
|
|
|
|
|
| |
This restores the alphabetical sort that was present
before the renaming of boardname.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
add pogoplug v4 envs support in uboot-envtools
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
| |
Drop the target specific detection function in favour of the generic
one provided by base-files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
|
| |
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
Use the generic function instead ot the target specific ones.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
|
|
|
|
|
| |
adding nsa325 envs for consistency with other kirkwoods
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
| |
accessing the u-boot's envs on this device is required to read the mac address.
These are the envs of the new u-boot, not of the stock one.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
|
|
|
|
|
|
|
|
|
|
| |
Few minor code formatting style fixes, including:
- keep one board per line
- always use "|\" (for consistency)
- remove redundant double quotes and empty lines
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
|
|
|
|
|
|
| |
Add board 'dockstar' to known fw_env-configurations.
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
|
|
|
|
|
|
| |
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47457
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
|
|
|
|
|
|
| |
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 44037
|
|
|
|
|
|
|
|
|
|
| |
- SheevaPlug
- SheevaPlug with eSATA
- GuruplugServerPlus
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
SVN-Revision: 43747
|
|
|
|
|
|
|
|
| |
http://wiki.openwrt.org/toh/linksys/ea3500
Signed-off-by: Dan Walters <dan@walters.io>
SVN-Revision: 43230
|
|
|
|
|
|
| |
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 41340
|
|
|
|
|
|
| |
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 40872
|
|
|
|
|
|
|
|
|
|
| |
The settings require that the OpenWrt provided u-boot is used as either
first or second stage bootloader as it modifies the partitioning scheme
to move the u-boot environment to a separate mtd partition.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
SVN-Revision: 40829
|
|
|
|
|
|
|
|
| |
Also, scripts can be installed as data so let's change that here too.
Signed-off-by: Luka Perkov <luka@openwrt.org>
SVN-Revision: 38403
|
|
SVN-Revision: 33781
|