summaryrefslogtreecommitdiff
path: root/target/linux/ipq806x/base-files/etc/hotplug.d
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-221-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: fix wireless macsHannu Nyman2017-02-031-1/+1
| | | | | | | | | | | | Commit 71a39b8 ("ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800") added a trailing TAB char after the backslash which prevents the assignment of the correct MACs for wifi devices. Fixes: FS#451 Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> [reworded commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: Fix wireless support for Netgear Nighthawk X4S D7800Zhang Jingye2017-01-182-11/+15
| | | | | | | | | | D7800 has a simular hardware to R7800 and uses dual QCA9980 for both 2.4GHz and 5GHz band. However there is no proper initialization for them, which causes a kernel panic due to failed firmware loading. This patch adds d7800 to ath10k caldata extraction list. I can get two functional wireless bands after making change to it. Signed-off-by: Zhang Jingye <934526987@qq.com>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-242-0/+9
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* ipq806x/nbg6817: add support for ZyXEL NBG6817André Valentin2016-10-261-0/+6
| | | | | | | | | | | | | | | | | CPU: 2x1.8GHz ARM, RAM: 512MiB Storage: 4MiB serial Flash, 3.9GiB MMC NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin to device. Then run: cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4 cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5 reboot -f For debugging serial console is easily visible on board, no soldering needed. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x: fix wlan mac for Netgear R7800Pavel Kubelun2016-10-061-0/+3
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: Build image for Netgear Nighthawk X4 R7500v2Alexis Green2016-08-221-0/+2
| | | | | | Signed-off-by: Alexis Green <alexis@cessp.it> [Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: enable ieee80211 phy hotplug and patch macaddressAdrian Panella2016-06-221-0/+23
| | | | | | | | Calibration data for QCA99x0 in this device has bogus macaddress. The data cannot be modified directly, as it breaks checksum control. Instead change the macaddress from phy add hotplug event. Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x: add initial support for Netgear R7800Pavel Kubelun2016-06-221-0/+6
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: base-files: add support for Linksys EA8500Adrian Panella2016-06-131-0/+8
| | | | Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x/base-files: extract ath10k caldataAsh Benz2016-05-271-0/+68
Signed-off-by: Ash Benz <ash.benz@bk.ru>
generated by cgit v1.1 at 2026-04-11 22:22:13 +0000